Team:BYU Provo/Team Thermosensor/Week8

From 2011.igem.org

Revision as of 08:08, 24 September 2011 by Cheddar3210 (Talk | contribs)

Team BYU Provo

BYU Provo
 

Week 8 (June 5 - 11)

  • 6/7
    • Added 6 ul loading dye to each PCR reaction tube and ran on gel @ 160 V for 17 min
      • Lane 1 - DNA ladder
      • Lane 2 - 24-1
      • Lane 3 - 24-2
      • Lane 4 - 24-3
    • It appears that lacZ amplified correctly, but pBAD did not for whatever reason, we had very little template left (PJG408) that could be part of the issue
  • 6/6/11
    • Ligation for pBAD into pPLAT; put in tube labeled Lig 23-1
      • 6.5 ul H2O
      • 1.5 ul 10x ligase buffer
      • 1 ul T4 ligase
      • *1 ul vector (23-2)
      • *1 ul insert (23-1)
      • - Incubate for 30 min at room temp
        • Transformation
          • Followed Dr. Grose’s procedures. Incubated in 37 degree incubator overnight. - Addison
          • Back on ice @ 3:27
          • Take out of incubator @ 4:13
  • 6/7
    • It appears that there is no cell growth on the plate labeled 6/6 23-1
    • Set up PCR for pBAD following volumes on prev. page
    • There is lacZ still in stock
    • Ran on “Phusion10” in Grose’s labe.
      • +25-1
        • pBAD recipe same as 24-1
      • We have pBAD!
    • PCR clean-up of pBAD
      • T26-1 PCRup w/ Dr. Grose
    • Low melt of T26-1 PCRup
      • Strong band, very nice looking
    • Cut out gel slice w/ Dr. Grose
    • pBAD GS T26-1
    • Ligation of pBAD w/ Dr/. Grose
      • Used insert: GS T26-1 and vector: GS T23-2
    • T26-1 pBAD + 23-2
      • Lig
      • 6.5 ul H2O
      • 1.5 ul 10x ligase buffer
      • 1 ul T4 DNA ligase
      • 3 ul vector
      • 3 ul insert
        • mix and sit for min
      • T26-1
        • Tran
          • T26-1 + 23-2
            • pBAD ligation transformed into E. coli DH5alpha
        • Plate
          • pBAD 26-1
          • pPLAT 23-2
          • Transformation
          • Placed in 37*C. If we have growth the next thing is colony PCR
          • We have growth!!
  • 6/9/11
    • Colony PCR 26-1
      • Took 8 colonies from plate T26-1 and swirled them in 50 ul of H2O and then plated on “T26-1 lig” and placed the plate in 37*C overnight
      • Took the PCR tubes with 50 ul of H2O + the 8 colonies + boiled in thermocycle - this will then be used as template for the colony PCR
        • 19 ul of H2O
        • 2.5 ul Rxn buffer
        • 0.5 ul 10mM dNTPs
        • 0.5 ul IG11 (forward) primers
        • 0.5 ul IG 12 (reverse) primers
        • 0.5 ul Phusion DNA polymerase
        • 2 ul boiled colony sample
      • Master Mix T26-1
        • 171 ul H2O
        • 22.5 ul 5x Rxn buffer
        • 4.5 ul 10 mM dNTPs
        • 4.5 ul IG11
        • 4.5 ul IG12
        • 4.5 ul Phusion polymerase
        • + add 2 ul boiled colony sample + 23.5 ul of master mix to each tube
          • Ran in Phusion 10
          • OOPS...USE Taq LIKE PROTOCOL CALLS FOR ON COLONY PCR...My bad
            • This was just the boiled template. I labeled the template and the PCR similarly, my fault...I will label the colony PCR as PCR next time + the template as “T” followed by a number.
            • Lanes 2-8=Tubes 1-8. No verification of insert. Will retry another colony PCR
          • Reused colonies 1-8 and boiled them from plate T-26-1
        • Master Mix A T26-A
          • 171 ul H2O
          • 22.5 ul 5x Rxn buffer
          • 4.5 ul 10 mM dNTPs
          • 4.5 ul IG11
          • 4.5 ul IG12
          • 4.5 Taq polymerase
          • add 2ul boiled colonies + 23.5 ul of this mix to each tube
        • Master Mix B T26-B
          • 171 ul H2O
          • 22.5 ul 5x Rxn buffer
          • 4.5 ul 10 mM dNTPs
          • 4.5 ul IG12
          • 4.5 ul IG38
          • 4.5 Taq polymerase
            • PCR: Ran 26-1 on a gel @165V for 18 min
              • It worked! It appears that we have pBAD in the pPLAT plasmid
                • Next step is to sequence the plasmid just to verify that it really worked and then we can put GFP and lacZ into the plasmid as well
                • No need to sequence...it’s a promoter