Team:Cambridge/Experiments/Assembly of Reflectin Constructs

This is a placeholder. We should fill it in.

Construct Design

Primer Design

We should mention expected lengths of products here.

Assembly: first attempt

PCR

In the first round of PCR, we amplified fragments required for the assembly of GA1, GA2, GA3 and GA4 constructs.

• We performed PCR using Phusion Hot Start DNA Polymerase in 20 μl reaction volume.
• The time profile used in the PCR machine was the following:

We decided to use the 55°C annealing temperaure, although the predicted temperature for most primers is 5-10°C higher, because of a low annealing temperature of the VF2 primer.

• Primers and template DNA provided by our supervisor Paul served as a positive control, but eventually we did not detect any products on the gels.

The pictures below present results of the gel electrophoresis of PCR products.

• In most cases position of a band matches the expected length of DNA fragment. The only exception are GA1-2 and GA3-2 products. According to the position on the gel the length of these DNA fragments is 4-5kb, whereas the predicted length is 3.5kb. Our hypothesis is that we were provided [http://partsregistry.org/Part:pSB1AK3 pSB1AK3] backbone instead of [http://partsregistry.org/Part:pSB1A3 pSB1A3] backbone.
• For GA1-1, GA2-1, GA3-1 and GA4-1 we obtained two bands: 1000bp and 400bp, with the latter resulting from non-specific priming most probably. We extracted the two bands for GA1-1, GA2-1 and GA4-1 products, labelling the 1000kb and 400bp fragments GAX-1a and GAX1-b respectively.
• The molecular weight marker that we used in all gels is HyperLadder I, which produces regularly spaced bands ranging from 200 to 10,000bp.

For the gel extraction of DNA we followed the protocol, assuming that one slice of gel is 100μl.

Gibson Assembly

We conducted Gibson Assembly of GA1, GA2, GA3 and GA4 constructs according to the protocol. The volumes of Master Mix and solutions of amplified DNA were the following:

Transformation

We transformed competent E.coli cells according to [Team:Cambridge/Protocols/Transformation_of_E.Coli | the following protocol]. We cultured each class of transformants on four different plates.

Results

After overnight incubation at 37°C of transformed E.coli cells, we could see colonies on only some of our plates. We examined successful plates under a fluorescence microscope to check if the cells had been transformed with a carry-through of the template DNA used in the initial PCR reactions. The risk of contaminating Gibson Assembly reactions with template DNA was fairly high because circular DNA of around 4kb was likely to co-localize with the linear PCR products.

These are the results of the examination of transformants:

We decided to conduct diagnostic colony PCR of E.coli transformed with GA1 and GA3 constructs, to confirm successful assembly of the plasmids. In addition, we performed a series of tests to identify the cause of the low efficiency of transformation. The proposed sources of error included:

• Low efficiency of DNA gel extraction
• Unsuccessful Gibson Assembly
• Low viability of competent E.coli cells

Diagnostics

In order to check if gel extraction of DNA was successful, we ran a 1% agarose gel with samples of purified products of the initial PCR reactions. Although we could see distinct, fairly thick bands on the first gels, from which components of Gibson constructs were purified, bands on the diagnostic gel are very faint, even missing in some lanes. This indicates that the yield of our extraction procedure was very low and probably that was the main reason why the performed transformation was fairly unsuccessful.

Therefore, we decided to repeat PCR reactions, this time at higher 50μl volume, and try different conditions of the gel extraction procedure.

Assembly: second attempt

PCR

In the second round of PCR, we amplified fragments required for the assembly of GA1, GA2, GA3, GA4, as well as GA5 and GA6 constructs.

• We performed PCR using Phusion Hot Start DNA Polymerase in 50 μl reaction volume.
• The time profile used in the PCR machine was the following, the same as the one used before:

We ran PCR products on a 1% agarose gel to separate amplified products from template DNA and primers, as well as to check how efficient and specific the amplification process was.

• In most cases position of a band matches the expected length of DNA fragment. The only exception are again 4-5kb GA1-2 and GA3-2 products, although the predicted length is 3.5kb.
• This time we obtained single bands on lanes with amplified reflectin, whereas we observed some additional bands on almost all lanes with amplified backbones of plasmids to be constructed. Most probably these were products of non-specific annealing, which we did not detect on the first gel due to low concentration of these additional products in 25μl reaction.

Moreover, these differences emphasize the fact that the amount of non-specific products of DNA amplification can vary greatly between reactions depending on the timing of random mis-annealing events.

• All components of GA5 and GA6 constructs produced clear fairly thick bands with positions matching expected lengths. No non-specific bands on GA5-1 (Reflectin A2) and GA6-1 (Reflectin 1B) lanes were observed.
• The molecular weight marker that we used in all gels is HyperLadder I, which produces regularly spaced bands ranging from 200 to 10,000bp.

Gibson Assembly

Transformation

Results

What next?