Team:UEA-JIC Norwich/Methods

From 2011.igem.org

(Difference between revisions)
Line 5: Line 5:
</head>
</head>
<body>
<body>
-
<STYLE>H2 {FONT-SIZE: 21pt; COLOR: #000080}High Efficiency Transformation Protocol</h2>
+
<h2>High Efficiency Transformation Protocol</h2>

Revision as of 09:22, 9 August 2011

University of East Anglia-JIC

UNIVERSITY OF EAST ANGLIA-JOHN INNES CENTRE

High Efficiency Transformation Protocol

1. Thaw a tube of NEB 5-alpha Competent E.coli cells on ice for 10 minutes

2. Mark the location of the Biobrick well (letters from top to bottom, numbers from left to right)

3. Resuspend specific biobrick part (1 μl) with distilled water (20 μl). Aspirate up and down a few times

4. Inoculate with DNA ( 1 μl) to the competent cells

5. Place the mixture on ice for 30 minutes. Do not mix

6. Heat shock at exactly 42°C for exactly 30 seconds. Do not mix

7. Place on ice for 5 minutes. Do not mix

8. Pipette 950 μl of room temperature SOC into the mixture

9. Place at 37°C for 60 minutes. Shake vigorously (250 rpm) or rotate

10. Warm selection plates to 37°C

11. Do serial dilutions (2-3) at 105. Mix cells, flick/invert gently

12. Spread (100 μl) on agar plates of each dilution

13. Incubate overnight at 37°C

Culture Preparation Protocol

1. Select a colony by sampling it with a wooden pick

2. Place into the appropriate antibiotic LB broth

3. Incubate at 37°C overnight in an Incubator Shaker

4. Store at -20°C

Glycerol Stock Solution Protocol

1. Take 500µL of a previously prepared culture and place into a screw-top eppendorf tube

2. Add 500µL of Glycerol solution (V.V 50% to make a 25% concentration

3. Place in -20°C storage

Qiagen miniprep Protocol

1. Resuspend pelleted bacterial cells in 250 µl Buffer P1 and transfer to a microcentrifuge tube.

2. Add 250 µl Buffer P2 and mix thoroughly by inverting the tube 4–6 times. If using LyseBlue reagent, solution turns blue.

3. Add 350 µl Buffer N3 and mix immediately and thoroughly by inverting the tube 4–6 times. If using LyseBlue reagent, solution turns colorless.

4. Centrifuge for 10 min at 13,000 rpm (~17,900 x g) in a table-top microcentrifuge.

5. Apply the supernatant (from step 4) to the QIAprep spin column by decanting or pipetting.

6. Centrifuge for 30–60 s. Discard the flow-through.

7. Recommended: Wash the QIAprep spin column by adding 0.5 ml Buffer PB and centrifuging for 30–60 s. Discard the flow-through. This step is only required when using endA+ or other bacteria strains with high nuclease activity or carbohydrate content (see QIAprep Miniprep Handbookfor more details)

8. Wash QIAprep spin column by adding 0.75 ml Buffer PE and centrifuging for 30–60 s.

9. Discard the flow-through, and centrifuge for an additional 1 min to remove residual wash buffer.

10. To elute DNA, place the QIAprep column in a clean 1.5 ml microcentrifuge tube. Add 50 µl Buffer EB or water to the center of each QIAprep spin column, let stand for 1 min, and centrifuge for 1 min.

Gel Electrophoresis Protocol

1. Measure 0.6g of agarose and add to 60 mL TAE Buffer

2. Mix throroughly

3. Heat until solution becomes clear

4. Allow to cool, then add 30µl of 1mg per ml Ethidium Bromide

5. Pour solution into gel tray with comb in place

6. Allow to set

7. Place in electrophoresis tank and submerge in TAE buffer

8. Pipette 10 µl of ladder into left most well

9. Perform serial dilution of sample

10. Add 9 µl of sample to 1 µl of loading dye and place in wells, noting position of each sample

11. Run gel at 90V for 30 minutes

2. Visualise using UV light

PCR Protocol

1. Program desired cycle into PCR machine. Cycle used was as follows:

94°C - Initial Denaturation - 120 seconds

94°C - 30 seconds

58-68°C - Gradient Cycle - 30 seconds

68°C - Final Extension - 150 seconds

68°C - 300 seconds

4°C - Hold

Second, third and fourth stages were repeated for 30 cycles.

2. Three serial dilutions were conducted, yielding concentrations of 1:10, 1:100, and 1:1000. This was carried out in order to find the optimum concentration of template DNA to use, as we didn't know the concentration yielded from the Miniprep Protocol used to extract the plasmid. We conducted a gradient cycle because even though we knew the annealing temperatures of the primers we'd designed, we wanted to make sure we had the optimum temperature range.