Team:Bielefeld-Germany/Results/S-Layer/SbpA
From 2011.igem.org
![](https://static.igem.org/mediawiki/2011/3/3c/Bielefeld-Germany2011-header-full.png)
![](https://static.igem.org/mediawiki/2011/c/c7/Bielefeld-header-results-s-layer.png)
Contents |
SbpA from Lysinibacillus sphaericus CCM 2177
The S-layer protein SbpA of Lysinibacillus sphaericus CCM 2177 consists of 1,268 amino acids and is encoded by the sbpA gene. The lattice symmetry formed through self-assembly is a square structure (p4) with a center-to-center spacing of the morphological units of 13.1 nm (see fig. 1). [http://pubs.acs.org/doi/abs/10.1021/bc800445r Badelt-Lichtblau et al. (2009)] found that the self-assembly process is strongly dependent on presence of bivalent cations. Therefore the assembly is dirigible, because in absence of bivalent cations SbpA stays water-soluble. At the amino-terminal end the protein consists of three typical SLH (S-layer homologous) domains and an additional 58 amino acid-long SLH-like motif. Those domains recognize a distinct type of secondary cell wall polymers (SCWP), consisting of disaccharide units. The S-layer protein SbpA is extremely resistant to deletions changing its properties. The deletion of up to 237 carboxy-terminal amino acids does not affect the ability to self-assemble into square lattices. After deletion of 350 amino acids the lattice structure changes from square (p4) to oblique (p1) symmetry [http://pubs.acs.org/doi/abs/10.1021/bc800445r (Badelt-Lichtblau et al., 2009)].
Expression in E. coli
The SbpA gene under the control of a T7 / lac promoter (<partinfo>K525403</partinfo>) was fused to mCitrine ([http://partsregistry.org/Part:BBa_J18931 BBa_J18931]) using Freiburg BioBrick assembly for characterization experiments.
The SbpA|mCitrine fusion protein was overexpressed in E. coli KRX after induction of T7 polymerase by supplementation of 0.1 % L-rhamnose and 1 mM IPTG using the autinduction protocol by Promega.
![](/wiki/images/3/38/Bielefeld_2011_405_Growthcurve.png)
![](/wiki/images/3/34/Bielefeld_2011_405_RFU_OD.png)
Purification of SbpA fusion protein
As seen in the analysis of the cultivations with expression of SbpA | mCitrine fusion proteins, these proteins form inclusion bodies in E. coli. Inclusion bodies have the advantage that they are relatively easy to clean-up and are resistant to proteases. So the first purification step is to solve and set-free the inclusion bodies. This step is followed by two filtrations (300 kDa UF and 100 kDa DF/UF) to further concentrate and purify the S-layer proteins. After the filtrations, the remaining protein solution is dialized against ddH2O for 18 h at 4 °C in the dark. The dialysis leads to a precipitation of the water-insoluble proteins. After centrifugation of the dialysate the water-soluble S-layer monomers remain in the supernatant and can be used for recrystallization experiments.
The fluorescence of some collected, important fractions of this purification strategy is shown in the following figure 4:
A lot of protein is lost during the purification especially after centrifugation steps (compared to filtrations). The fluorescence in the urea containing fractions is lowered due to denaturation of the fluorescent protein. This purification strategy is very simple and can be carried out by nearly everyone in any lab being one first step to enable real do it yourself nanobiotechnology.
Final purification strategy
Scheme of purification strategy for SbpA (fusion) proteins:
First, SbpA is expressed in E. coli under the control of a T7 / lac promoter for separation of growth and production phase due to metabolic stress of the S-layer expression. Because the SbpA protein is forming inclusion bodies in E. coli, an inclusion body purification with urea follows the cell lysis. The S-layers are further concentrated and purified by two ultrafiltration / diafiltration steps (300 kDa and 100 kDa) and afterwards dialysed against water leading to the precipitation of water-insoluble proteins. The supernatant contains the monomeric SbpA solution.
Click for detailed information
Alternative purification strategy
Sometimes the inclusion body purification does not give very clean fractions. That's why we developed another purification strategy for <partinfo>K525405</partinfo> monomers after inclusion body purification. This strategy consists of a capture with an IEX followed by a purification with HIC. Because of issues with the PES membranes we used to rebuffer our samples (see below - PES binds most of the S-layers) we lost a lot of our proteins in this step between the two chromatographies. So there was not enough protein left to colour it with Coumassie in an SDS-PAGE and time ran out to perform a silver staining. The fluorescence of the collected fractions of the chromatographies is shown in the figures below.
![](/wiki/images/0/00/Bielefeld_Germany-405IEX.png)
![](/wiki/images/c/ca/Bielefeld_Germany-405HIC.png)
Immobilization behaviour
After purification, solutions of monomeric SbpA S-layer proteins can be recrystallized and immobilized on silicon dioxide beads in recrystallization buffer (0.5 mM Tris-HCl, pH 9, 10 mM CaCl2). After the recrystallization procedure the beads are washed with and stored in ddH2O at 4 °C in the dark. The fluorescence of the collected fractions of a recrystallization experiment with <partinfo>K525405</partinfo> are shown in Fig. 7. 100 mg beads were coated with 100 µg of protein. The figure shows, that not all of the protein is immobilized on the beads (supernatant fraction) but the immobilization is pretty stable (very low fluorescence in the wash). After the immobilization, the beads show a high fluorescence indicating the binding of the SbpA | mCitrine fusion protein.
Optimal bead to protein ratio for immobilization
To determine the optimal ratio of silica beads to protein for immobilization, the degree of clearance ϕC in the supernatant is calculated and plotted against the concentration of silica beads used in the accordant immobilization experiment (compare fig. 8):
The data was collected in three indipendent experiments. The fluorescence of the samples was measured in the supernatant of the immobilization experiment after centrifuging the silica beads. The fluorescence of the control was measured in a sample which was treated exactly like the others but no silica beads were added. 100 µg protein was used for one immobilization experiment. The data was fitted with a sigmoidal dose-response function of the form
with the Hill coefficient p, the bottom asymptote A1, the top asymptote A2 and the switch point log(x0) (R² = 0.997).
The fit indicates that a good silica concentration for 100 µg of protein is 200 - 250 mg mL-1. This set-up leads to saturated beads with low waste of protein. So a good protein / bead ratio to work with is 7 - 9 * 10-4.