From 2011.igem.org

(Difference between revisions)

Revision as of 21:24, 28 October 2011

SgsE from Geobacillus stearothermophilus NRS 2004/3a

Oblique structure of S-layer lattices.

SgsE monomers are naturally assembled in a lattice with oblique symmetry (p2) (compare figure on the right) exhibiting a well-defined periodicity and distances of 9.4 – 11.6 nm between the proteinaceous subunits. The S-layer protein SgsE of Geobacillus stearothermophilus NRS 2004/3a consists of 903 amino acids, including a 30 amino acid signal peptide (SLH-domain) at the amino-terminus. The carboxy-terminal part of SgsE is the larger part of the protein, encoding the self-assembly information. The protein is formed by the sgsE gene, has a calculated mass of 93.7 kDa and an isoelectric point of 6.1. When isolated SgsE maintains its ability to self-assemble, and depending on salt concentration, duration of dialysis to remove the detergent and its amino acid sequence it builds up five types of self-assembly products. These products are formed like flat sheets and cylinders ([http://onlinelibrary.wiley.com/doi/10.1002/smll.200700200/abstract Schäffer et al., 2007]).

Expression in E. coli

The SgsE gene under the control of a T7 / lac promoter (<partinfo>K525303</partinfo>) was fused to mCitrine ([http://partsregistry.org/Part:BBa_J18931 BBa_J18931]) using Freiburg BioBrick assembly for characterization experiments.

The SgsE|mCitrine fusion protein was overexpressed in E. coli KRX after induction of T7 polymerase by supplementation of 0.1 % L-rhamnose and 1 mM IPTG using the autinduction protocol by Promega.

Figure 1: Growth curve of E. coli KRX expressing the fusion protein of SgsE and mCitrine with and without induction, cultivated at 37 °C in autoinduction medium with and without inductor, respectively. A curve depicting KRX wildtype is shown for comparison. After induction at approximately 4 h the OD₆₀₀ of the induced <partinfo>K525305</partinfo> visibly drops when compared to the uninduced culture. Both cultures grow significantly slower than KRX wildtype probably due to a leaky promoter and metabolic stress by the high copy plasmid.

Figure 2: RFU to OD₆₀₀ ratio of E. coli KRX expressing the fusion protein of SgsE and mCitrine with and without induction. A curve depicting KRX wildtype is shown for comparison. After induction at approximately 4 h the RFU to OD₆₀₀ ratio starts to rise in the induced culture. Compared to the uninduced culture the ratio is roughly four times higher. The KRX wildtype shows no variation in the RFU to OD₆₀₀ ratio.

Purification of SgsE fusion protein

Purification without His-tag

As observed in the analysis of the cultivations with expression of SgsE | mCitrine fusion proteins, these proteins form inclusion bodies in E. coli. Inclusion bodies have the advantage that they are relatively easy to clean-up and are resistant to proteases. So the first purification step is to isolate and solubilize the inclusion bodies. This step is followed by two filtrations (300 kDa UF and 100 kDa DF/UF) to further concentrate and purify the S-layer proteins. After the filtrations, the remaining protein solution is dialyzed against ddH₂O for 18 h at 4 °C in the dark. The dialysis leads to a precipitation of the water-insoluble proteins. After centrifugation of the dialysate the water-soluble S-layer monomers remain in the supernatant and can be used for recrystallization experiments.

The fluorescence of the collected fractions of this purification strategy is shown in the following figure 3:

Figure 3: Fluorescence of collected fractions during purification of <partinfo>K525305</partinfo> fusion protein.

A lot of protein is lost during the purification especially after centrifugation steps. The fluorescence in the urea containing fractions is lowered due to denaturation of the fluorescent protein. Some fluorescence could be regenerated by the recrystallization in HBSS. This purification strategy is very simple and can be carried out by nearly everyone in any lab being one first step to enable real do it yourself nanobiotechnology.

Purification with His-tag

By fusing the SgsE | mCitrine with a C terminal [http://partsregistry.org/Part:BBa_K157011 His-6-tag] the S-layer protein could be simply purified by using a denaturating His-tag affinity chromatography. This purification strategie has the advantage that no time-consuming and complex inclusion body purification and filtration is necessary to decrease the amount of native E. coli proteins. Additional to the simplification a higher purity could of the S-layer protein could be reached.

This purification was made using the SgsE fusion protein containing a N terminal mCitrine,for identification and a C terminal His-6-tag. The SDS-PAGE gel (fig. 4) and the fluorescence (fig. 5) in the collected fractions showed that the majority of fusion protein was eluated with a imidazole concentration of ca. 50 mM. There was also fluorescence measurable in the flowthrough and wash fractions. This indicates that the used 1 mL HisTrap FF crude (GE Healthcare) was overloded or the protein was bound weakly at to the affinity matrix. The resulting purity in the elution fraction, the saving of time and the easiness makes this procedure to the preferd purification method.

Fig. 4: SDS-PAGE gel of a denaturating immobilized metal affinity chromatography (IMAC) of a SgsE fusion protein containing a N terminal mCitrine and a C terminal His-6-tag. A 1 mL HisTrap FF crude by GE Healthcare (Ni-NTA) was used for purification. The binding buffer contained 10 mM imidazole and the elution buffer (buffer B) 500 mM imidazole. The bound proteins were eluated by a stepwise rising imidazole gradient (10 % buffer B per step). The SgsE fusion protein (111,2 kDa) was eluated in the 10 % buffer B fraction in a high purity.

Fig. 5: Fluorescence in the fractions of a denaturating immobilized metal affinity chromatography (IMAC) of a SgsE fusion protein containing a N terminal mCitrine and a C terminal His-6-tag. A 1 mL HisTrap FF crude by GE Healthcare (Ni-NTA) was used for purification. The binding buffer contained 10 mM imidazole and the elution buffer (buffer B) 500 mM imidazole. The bound proteins were eluated by a stepwise rising imidazole gradient (10 % buffer B per step). The SgsE fusion protein (111,2 kDa) was eluated in the 10 % buffer B fraction in a high purity.

Final purification strategies

Strategy with His-tag Scheme of purification strategy for SgsE (fusion) proteins with His-tag:

IGEM-Bielefeld2011-322 Aufreinigung symbol.png

First, SgsE is expressed in E. coli under the control of a T7 / lac promoter for separation of growth and production phase due to metabolic stress of the S-layer expression. Because the SgsE protein is forming inclusion bodies in E. coli the

Strategy without His-tag

Scheme of purification strategy for SgsE (fusion) proteins without His-tag:

Bielefeld-Germany2011-305 405-Aufreinigung symbol.png

First, SgsE is expressed in E. coli under the control of a T7 / lac promoter for separation of growth and production phase due to metabolic stress of the S-layer expression. Because the SgsE protein is forming inclusion bodies in E. coli, an inclusion body purification with urea follows the cell lysis. The S-layers are further concentrated and purified by two ultrafiltration / diafiltration steps (300 kDa and 100 kDa) and afterwards dialysed against water leading to the precipitation of water-insoluble proteins. The supernatant contains the monomeric SgsE solution.

Click for detailed information

Immobilization behaviour

After purification, solutions of monomeric SgsE S-layer proteins can be recrystallized and immobilized on silicon dioxide beads in HBSS (Hank's buffered saline solution). After the recrystallization procedure the beads are washed with and stored in ddH₂O at 4 °C in the dark. The fluorescence of the collected fractions of a recrystallization experiment with <partinfo>K525305</partinfo> are shown in fig. 6. 100 mg beads were coated with 100 µg of protein. The figure shows, that not all of the protein is immobilized on the beads (supernatant fraction) but the immobilization is pretty stable (very low fluorescence in the wash). After the immobilization, the beads show a high fluorescence indicating the binding of the SgsE | mCitrine fusion protein.

Figure 6: Measured fluorescence of collected fractions of immobilization of purified <partinfo>K525305</partinfo> on silica dioxide beads (n = 3, 100 mg mL^-1 SiO₂, time of recrystallization: 4 h).

Optimal bead to protein ratio for immobilization

To determine the optimal ratio of silica beads to protein for immobilization, the degree of clearance ϕ_C in the supernatant is calculated and plotted against the concentration of silica beads used in the accordant immobilization experiment (compare fig. 7):

(2)

The data was collected in three independent experiments. The fluorescence of the samples was measured in the supernatant of the immobilization experiment after centrifugation of the silica beads. The fluorescence of the control was measured in a sample which was treated exactly like the others but no silica beads were added. 100 µg protein was used for one immobilization experiment. The data was fitted with a sigmoidal dose-response function of the form

(3)

with the Hill coefficient p, the bottom asymptote A1, the top asymptote A2 and the switch point log(x₀) (R² = 0.874).

The fit indicates that a good silica concentration for 100 µg of protein is 150 - 200 mg mL^-1. This set-up leads to saturated beads with low waste of protein. So a good protein / bead ratio to work with is 5 - 7 * 10^-4.

Figure 7: Degree of clearance of the fluorescence in the supernatant plotted against the concentration of silicium dioxide beads used to immobilize <partinfo>K525305</partinfo> (n = 3). Data is fitted with dose-reponse function (R² = 0.874).

@@ Line 44: / Line 44: @@
 '''Strategy with His-tag'''
+Scheme of purification strategy for SgsE (fusion) proteins with His-tag:
 [[Image:IGEM-Bielefeld2011-322_Aufreinigung_symbol.png|800px|center]]
+First, SgsE is expressed in ''E. coli'' under the control of a T7 / lac promoter for separation of growth and production phase due to metabolic stress of the S-layer expression. Because the SgsE protein is forming inclusion bodies in ''E. coli'' the
 '''Strategy without His-tag'''

Team:Bielefeld-Germany/Results/S-Layer/SgsE