Microfluidic Channel Design

For implementation of the SmoColi system, a channel is needed to establish a small molecule gradient (see Circuit Design). However, there were several different possible channel designs, and the final design evolved through an iterative series of design steps and design validations. The first designs were validated based on vast simulations, the final design furthermore by biological experiments in the lab (see Systems Validation).

Microfluidic channel with flow and recycling of the medium

We came up with two different possible microfluidic channel designs, both involving immobilized cells and a flow of medium containing inducer molecules through the channel. By having a flow and degradation, we could obtain a gradient of the inducer molecule. Because of the flow, our cells would also be constantly supplied with nutrients from the medium.

• Variant 1: Microfluidic channel with agarose-immobilized cells in cubic pockets

This channel design consists of two layers: The bottom one is a polydimethylsiloxane (PDMS) plate with regular cubic pockets. These pockets are filled with agarose-immobilized cells by letting the cell-agarose suspension flow over the pockets from the top by gravity. After washing the channel, cells would only be retained in the pockets.

The top layer is the actual PDMS channel, which is several pixels wide and several pixels high. Although this setup is rather complex, it has the advantage of having immobilized cells and thus being more robust, i.e. we could vary flow speeds or even put aerosol in the channel without the cells being washed out. Additionally, cell density can be varied very easily in this design as the cells can be diluted before being immobilized in agarose.

Figure 1: Experimental setup for SmoColi channel, Variant 1.

Video 1: Evaluation of the model.

• Variant 2: Microfluidic channel with cells sitting in pockets inside the channel

This channel design only consists of one part: A PDMS channel that is fixed onto a glass carrier. The PDMS channel contains pockets which "trap" the cells given a constant flow from the direction of the "open end" of the pockets. This channel design does not have the advantages of the above one, i.e. it is not as robust and cell density cannot be reliably varied. However, manufacturing it is a standard process and thus it is easier.

Figure 2: Experimental setup for SmoColi channel, Variant 2. The flow is supplied from the right side of the illustration.

Problems with these design variants:

A problem with both of these designs is that for the AHL-based RFP alarm to work, recycling of the flow back into the channel would be required. AHL-producing cells are only those "after" the GFP band, i.e. those at lower acetaldehyde concentration than the band concentration range. As long as the GFP band has not arrived to the end of the channel, we should make sure that there is AHL everywhere in the channel, so that it inhibits RFP production in every cell. Modeling showed that AHL can not simply diffuse "backwards" against the flow, but by having a recycling all the cells would be supplied with AHL and thus the alarm won't be activated before time.

However, since the tubing and pumps would have very high volumes compared to the channel's volume, the AHL signal would be diluted to the point where no detection is possible anymore. Also, several pumps would be required to accomplish this, further complicating the process design and making it more error-prone.

Improved microfluidic channel without flow

Figure 3: Experimental setup for SmoColi, a tube with no flow, diffusion only

Modeling showed that diffusion and degradation of the inducer are enough to create a concentration gradient in the channel. We also validated this by experiment. We engineered E. coli strain JM101 to express GFP upon IPTG induction and immobilized them in a small tube to which we attached an IPTG reservoir. After overnight incubation an IPTG-inducible GFP gradient was observed. The experiment confirmed the modeling results. Our cells survived and we concluded that we do not need constant supply of nutrients. For more information about this experimental setup and quantification of the results click here.

Problem with this design variant:

No live imaging is possible, but only end point measurements, since the agarose with cells first has to be taken out of the tube and then analyzed under microscope.

Further improvements: Microfluidic Channels with epoxy, molten parafilm or silicon

Since with the tube live imaging is not possible, we returned to microfluidics again and improved our channel design further. In order to image the channel at its top and bottom a glass slide is needed. We tried to build the channel by using a plastic mask and casting the boundaries with different materials. We tried a two-component glue, silicon and molten parafilm.

Figure 4: Tube (up) and plastic mask for channel construction (bottom)

Figure 5: Construction of microfluidic channels with silicon glue (left) and epoxy (right)

Problems with this design:

The glue turned out to be toxic for our cells.
We could also not use molten parafilm, since after putting it on the mask, the parafilm stuck to it and we couldn't separate them both (for molten parafilm a plastic mask is needed).
For silicon, we avoided the problem of it sticking to the mask by covering the mask in oil. However, we had a problem with closing the channel tightly to prevent evaporation.

Final Design: Microfluidics channel with PDMS

Finally, we decided to construct our channels out of something more frequently used: PDMS (polydimethylsiloxane), with a technique called photolithography. Advantages of PDMS are that it is cheap, optically clear and permeable to several substances, including gases (air can quickly diffuse through) [1]. For the PDMS as well, as for the silicon channel we had problems with water evaporation. In order to solve this issue, in our final experimental setup we incubated the channel in a petri dish full of water.
We constructed the PDMS channels ourselves, which was a very fun and interesting process. Our final design and the channel construction is explained in details here.

References

[1] [http://www.elveflow.com/microfluidic/16-start-with-microfluidic http://www.elveflow.com/microfluidic/16-start-with-microfluidic]