Team:ETH Zurich/Overview/CircuitDesign

From 2011.igem.org

(Difference between revisions)
(Circuit Design)
(SmoColi - Circuit Design)
 
(49 intermediate revisions not shown)
Line 1: Line 1:
-
{{:Team:ETH Zurich/Templates/Header/Overview|currPage=CircuitDesign}}
+
{{:Team:ETH Zurich/Templates/HeaderNew}}
-
{|class="roundContainer"
+
-
|style="font-size:2em; height: 30px" class="overview"|Circuit Design
+
-
|-
+
-
|'''Page description goes here.'''
+
-
|}
+
-
{|class="roundContainer"
+
{{:Team:ETH Zurich/Templates/SectionStart}}
-
|
+
= SmoColi - Circuit Design =
-
=== Signal Pre-Processing ===
+
To realize the smoke sensor (see [[Team:ETH_Zurich/Overview/Project|Project Idea]]), we implemented three distinct network designs: one SmoColi sensing acethaldehyde (see Figure 1), one sensing xylene (see Figure 2) and one sensing arabinose (see Figure 3). All designs share the same '''signal pre-processing''', '''processing units''', and a similar design in the '''signal detection unit'''.
-
The first step for both designs is to map an absolute acetaldehyde (xylene) concentration into a spatial signal. This first step is done in a channel by diffusion and degradation of acetaldehyde (xylene) a spatial gradient is produced.
+
-
=== Signal Detection ===
+
{|style="border: none;" align="center"
-
[[File:Design2.png|400px|left|thumb|'''Figure 1: Molecular mechanism of SmoColi with acetaldehyde sensor ''' ]]
+
|valign="top"|[[File:Design2.png|450px|center|thumb|'''Figure 1: Molecular mechanism of SmoColi with acetaldehyde sensor.''' ]]
-
[[File:Alternative_Xylene_system.png|400px|right|thumb|'''Figure 2: Molecular mechanism of SmoColi with xylene sensor.''' ]]
+
|valign="top"|[[File:Alternative_Xylene_system.png|450px|center|thumb|'''Figure 2: Molecular mechanism of SmoColi with xylene sensor.''']]
-
<br clear="all" />
+
|}
-
For Design&nbsp;1 (Design&nbsp;2), the small signaling molecule acetaldehyde (xylene) is supplied in the extra-cellular medium. Acetaldehyde (xylene) can diffuse through cellular membranes and dimerizes with its constitutively expressed receptor AlcR (XylR). Upon dimerizing, the AlcR-acetaldehyde (XylR-xylene) complex can bind to its operator, and inhibits (activates) the transcription of the genes under the control of the AlcR (XylR) promoter.
+
[[File:Arabinose system.png|450px|center|thumb|'''Figure 3: Circuit operations of SmoColi with arabinose sensor''' ]]
-
 
+
-
Since for the further signal processing it was necessary to have a POPS signal proportional to the signaling molecule concentration, and since the acetaldehyde sensor inverts the signal due to its transcriptional inhibition, we decided to include an additional unit to invert the transduced signal downstream of acetaldehyde, which is not present for the xylene sensor: we put TetR under the transcriptional control of AlcR, and since TetR acts as a transcriptional inhibitor for downstream proteins, the transduced acetaldehyde signal has a similar qualitative input/output relation as the transduced xylene sensor without inverter.
+
-
=== Signal Processing I: the Band-Pass Filter ===
+
For a detailed '''explanation''' about how the circuit works [[Team:ETH_Zurich/Overview/Informationprocessing#Signal_Processing |click here]].
-
[[File:ETH_states_of_bandpass.png|300px|right|thumb|'''Circuit operations for SmoColi''' exposed to medium, low and zero xylene concentration resulting in a GFP band. Triangles indicating the gradient of AHL (blue) and sensor molecule (violett), receptively. Non active interactions and non expressed Proteins are indicated light colors.]]
+
-
To realize the spatial green fluorescence band indicating the acetaldehyde (xylene) concentration, we implemented a signal processing unit, which transduces the incoming signal if and only if the signal is neither too strong nor too weak (band-pass filter [[#Ref2|[2]]]):
+
{{:Team:ETH Zurich/Templates/SectionEnd}}
-
TetR represses (XylR enhances) the expression of the LacI<sub>M1</sub> repressor (codon-modified LacI) and the lambda repressor CI. Thus, high acetaldehyde (xylene) concentrations result in high cytoplasmic levels of CI and of LacI<sub>M1</sub>. Since LacI<sub>M1</sub> represses the expression of the green fluorescent protein (GFP), no green fluorescence signal can be detected for high concentrations.
+
{{:Team:ETH Zurich/Templates/HeaderNewEnd}}
-
 
+
-
Low acetaldehyde (xylene) concentrations result in low LacI<sub>M1</sub> and CI concentrations. Although in this case, LacI<sub>M1</sub> does not repress GFP production, GFP is transcriptional repressed by the non-codon modified LacI, which is expressed at low CI concentrations.  Only intermediate signals results in a moderate level of CI and LacI<sub>M1</sub>. The repression of CI is significantly higher than the one of  LacI<sub>M1</sub>. While moderate levels of CI effectively shuts off LacI expression, the LacI<sub>M1</sub> concentration is to low to repress GFP
+
-
 
+
-
=== Signal Processing II: the Alarm Signal ===
+
-
To realize the alarm signal for toxic acetaldehyde (xylene) concentrations, we put the N-Acyl homoserine lactone (AHL) Synthase LuxI under the transcriptional control of CI, which is thus expressed only at low acetaldehyde (xylene) concentrations. LuxI syntesizes the small signaling molecule AHL which can quickly diffuse through the cell membrane in the extracellular space. Due to its relatively high diffusion constant, AHL diffuses through the whole tube and, thus, is present even in cells where no AHL is produced. Inside a cell, AHL can bind to its constitutively expressed receptor protein LuxR, and the thus activated LuxR represses the transcription of a red fluorescent protein (RFP). Thus, if the acetaldehyde concentration is below a threshold at least for a large enough minority of the cells in the channel, RFP is repressed in all cells. Only if the acetaldehyde concentration is above the threshold for all cells, no AHL is present in the channel and RFP is produced. Thus, the alarm signal RFP can be used to signal critical and potentially dangerous acetaldehyde (xylene) concentrations.
+
-
|}
+

Latest revision as of 20:36, 28 October 2011

Can you feel the smoke tonight?
 

Contents

SmoColi - Circuit Design

To realize the smoke sensor (see Project Idea), we implemented three distinct network designs: one SmoColi sensing acethaldehyde (see Figure 1), one sensing xylene (see Figure 2) and one sensing arabinose (see Figure 3). All designs share the same signal pre-processing, processing units, and a similar design in the signal detection unit.

Figure 1: Molecular mechanism of SmoColi with acetaldehyde sensor.
Figure 2: Molecular mechanism of SmoColi with xylene sensor.
Figure 3: Circuit operations of SmoColi with arabinose sensor

For a detailed explanation about how the circuit works click here.


Back to iGEM Our Sponsors
ETHZ-BASF.png ETH Zurich Logo.png ETHZ-Lonza.png ETHZ-Merck Serono.png
ETHZ-Novartis.png ETHZ-Roche.png ETHZ-Syngenta.png DSM MasterLogo.png