Team:Washington/Alkanes/Results

From 2011.igem.org

(Difference between revisions)
(The FabBrick, a module for even chain length alkane production)
 
(78 intermediate revisions not shown)
Line 2: Line 2:
__NOTOC__
__NOTOC__
-
===GC-MS analysis shows that our alkane production system is working===
+
<center><big><big><big><big>'''Diesel Production: Results Summary'''</big></big></big></big></center><br><br>
-
We preformed GC-MS analysis on cell cultures expressing both Acyl-ACP reductase(AAR) and Aldehyde Decarbonylase(ADC). to act as controls and in order to show that the alkane production system is working as expected, we also analyzed cell cultures expressing either only AAR, or only ADC.
+
-
[[File:Washinton_AARADCGC-MS.png|center|700px|thumb|GC plot showing that alkanes are only produced when both ADC and AAR are expressed.]]
+
-
===No significant  hydrocarbons peaks in samples extracted from cells expressing  only ADC===
+
-
No significant peaks are found on the ADC-Only control GC plot within the time range that we expect alkane signal based upon GC-MS runs on chemical standards(8-10.5 minutes). This is expected, as ''E. coli'' does not normally produce any  long chain length  aldehyde substrates.
+
-
===C16-Alcohol production by cells expressing AAR===
+
-
The GC plot from the extraction from a cell culture expressing only AAR shows a significant peak at 10.2 minutes corresponding to the C16 alcohol( as confirmed by comparison of the peak's MS spectra to a reference library). ''E. coli'' produces multiple aldehyde dehydrogenases that convert aldehydes to alcohols. The production of C16 alcohols in cells expressing AAR( but not in cells expressing only ADC) is consistent with AAR reducing  even chain length Acyl-ACPs into even chain length fatty aldehydes, which are further reduced by aldehyde dehydrogenases to the alcohol.
+
-
=== Alkane production by cells expressing ADC and AAR===
+
-
In cells expressing ADC and AAR, we saw peaks corresponding to the C13(8.2min) and C15(9.2min) alkanes, as well as a peak at 10.2 minutes that contains both the C16 alcohol and the C17 alkene. The fact that the C17 alkene and C16 alcohol peak overlaps with the C16 alcohol peak makes quantification of C17 akene yields impossible, but we have sufficient evidence to determine that both molecules are present in the 10.2 minute peak( the earlier section of the peak has an MS spectrea consistant with the C16 alcohol, and the later section is consistent with the C17 alkene). The C13 and C15 alkane peaks showed MS spectrums highly consistent with C13 and C15 alkane reference spectra. In addition, both alkane molecules eluted off of the GC at the same time as C13 and C15 alkane standards, further increasing confidence that the 8.2 min and 9.2 min peaks do correspond to the C13 and C15 alkanes. Odd chain length alkane production is what is expected from our system, as ADC removes a carbonyl group from even chain lengtrh aldehydes produced by AAR, yielding an odd chain length alkane.
+
-
===Quantification of alkane yield===
+
='''GCMS confirms The PetroBrick enables diesel production from sugar using ''E. coli'''''=
-
In order to be able to know how much alkane was being produced by our ''E. coli'', we spiked known amounts of alkane into cell cultures known to not produce alkanes. We then extracted using ethyl acetate, and analyzed extracts using GC-MS. Since peak area corresponds to the amnount of each substance present, we used these GC plots to make a standard curve that allows us to convert peak area into an absolute amount. To determine how much alkane was being produced by our alkane production construct, we grew up 3 E. coli cultures expressing ADC and AAR in a standard M9 media(link), and analyzed using GC-MS.
+
-
[[File:Washinton 2011 Pre-Optimization Quant.png|center|700px|thumb|Diagram showing yields of the C13 and C15 alkanes]]
+
We performed GC-MS analysis on extracts from cell cultures expressing both [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590032 Acyl-ACP Reductase] (AAR) and [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590031 Aldehyde Decarbonylase] (ADC) (this composite part is designated [http://partsregistry.org/Part:BBa_K590025 The PetroBrick]). To act as controls and in order to show that the alkane production system is working as expected, we also analyzed cell cultures expressing either only AAR, or only ADC.
-
[[File:Washinton 2011 Optimization Quant.png|center|700px|thumb|Diagram showing yields of the C13 and C15 alkanes]]
+
 +
[[File:Washington PetroBrick.png|300px|frameless|border|left|link=http://partsregistry.org/wiki/index.php?title=Part:BBa_K590025]]
 +
[[Image:Washinton_AARADCGC-MS.png|center|600px|thumb|GCMS confirms PetroBrick diesel production from sugar using E. coli]]
 +
<br>
-
[[File:Washington_alkane_yield.png|center|400px|thumb|Diagram showing yields of the C13 and C15 alkanes]]
+
'''No significant hydrocarbons peaks in samples extracted from cells expressing only ADC.'''  The blue GCMS chromatagram trace on the bottom show no significant peaks are found on the ADC only control within the time range that we expect alkane signal based upon GC-MS runs on chemical standards (8-10.5 minutes). This is expected, as ''E. coli'' does not normally produce any long chain length aldehyde substrates.
 +
 
 +
'''C16 alcohols are observed when AAR is expressed on its own.'''  The red GCMS chromatagram trace in the middle has a significant peak at 10.2 minutes corresponding to the C16 alcohol (as confirmed by comparison of the peak's MS spectra to a reference library) is observed when AAR is expressed in MG1655 E. coli.  The production of C16 alcohols in cells expressing AAR (but not in cells expressing only ADC) is consistent with AAR reducing even chain length Acyl-ACPs into even chain length fatty aldehydes, which are further reduced by aldehyde dehydrogenases to the alcohol.
 +
 
 +
'''The PetroBrick Works!  C13, C15, and C17 alkanes are produced when both AAR and ADC are expressed.''' 
 +
[[File:Washington2011 Spectra.png|right|550px|thumb|Comparasion of the  NIST reference C15 alkane spectrum( in blue) to the  C15 peak spectrum taken from a PetroBrick culture (in red). Note the strong m/z peak at 212, corresponding to the parent ion of the C15 alkane. For spectra of the C13 alkane and C17 alkene, refer to our [https://2011.igem.org/Team:Washington/Alkanes/spectra Spectra Page.]]]
 +
The green GCMS chromatagram trace in the middle has a significant new peaks corresponding to the C13 (8.2min) and C15 (9.2min) alkanes, as well as a peak at 10.2 minutes that contains both the C14 alcohol and the C17 alkene. The fact that the C17 alkene  peak overlaps with the C14 alcohol peak makes exact quantification of C17 akene yields impossible, but we have sufficient evidence to determine that both molecules are present in the 10.2 minute peak( the earlier section of the peak has an MS spectra consistent with the C16 alcohol, and the later section is consistent with the C17 alkene). The C13 and C15 alkane peaks showed MS spectra highly consistent with C13 and C15 alkane reference spectra(for these spectra, as well as the C17 alkene spectrum, refer to our [https://2011.igem.org/Team:Washington/Alkanes/spectra Spectra Page.]). In addition, both alkane molecules eluted off of the GC at the same time as C13 and C15 alkane standards, further increasing confidence that the 8.2 min and 9.2 min peaks do correspond to the C13 and C15 alkanes. Odd chain length alkane production is what is expected from our system, as ADC removes a carbonyl group from even chain length aldehydes produced by AAR, yielding an odd chain length alkane. Using the PetroBrick, we can turn simple sugars into diesel, a fuel fully compatible with modern infrastructure.
 +
 
 +
 
 +
----
 +
 
 +
='''Initial Quantization of Alkane Production'''=
 +
In order to be able to know how much alkane was being produced by our ''E. coli'', we spiked known amounts of alkane into cell cultures known to not produce alkanes. We then extracted using ethyl acetate, and analyzed extracts using GC-MS. Since peak area corresponds to the amount of each substance present, we used these GC plots to make a standard curve that allows us to convert peak area into an absolute yield. To determine how much alkane was being produced by the Petrobrick, we grew up 3 MG1655 cell cultures transformed with the PetroBrick in M9 production media ([https://2011.igem.org/Team:Washington/alkanebiosynthesis link]), and analyzed using GC-MS.
 +
 
 +
[[File:Washington_alkanestandardcurve.png|right|450px|thumb|Standard curves for converting peak area to an absolute amount. Note that these curves is almost perfectly linear. In addition, the curve generated from each alkane is nearly identical, allowing us to use 1, average curve for all 3 different alkanes.]]
 +
[[File:Washinton 2011 Pre-Optimization Quant.png|left|450px|thumb|Diagram showing yields of the C13 and C15 alkanes. Note: The C17 alkene is not included due to inability to quantify.]]
 +
 
 +
 
 +
 
 +
 
 +
 
 +
----
 +
 
 +
='''Optimized Production'''=
 +
By optimizing the method of growth, media, vectors, and cell line we were able to successfully increase alkane yield over 80-fold.  Note that this improvement doesn't include C17 alkene production, as we were unable to quantify the C17 alkene peak due to co-elution with the C14 alcohol. The parameters we adjusted for optimization are discussed in detail at [https://2011.igem.org/Team:Washington/Alkanes/Future/Vector our systems optimization] page under future directions, as this is an on going process.
 +
 
 +
[[File:Washinton 2011 Optimization Quant.png|center|550px|thumb|Our optimized growth conditions resulted in an 80 fold increase in total alkane yield.]]
 +
='''The FabBrick, a module for even chain length alkane production'''=
 +
In order to more closely match the composition of diesel, we wanted a way to make the C14 and C16 alkanes, something that has never been reported before in the literature. For a detailed account of how we achieved this please see our  [https://2011.igem.org/Team:Washington/Alkanes/Future/FabH2 future directions page].  But a brief summary of our results is as follows:
 +
 
 +
We found an enzyme, FabH2 from ''Bacillus subtilis'' that has been hypothesized to start fatty acid biosynthesis with a 3 carbon unit instead of the normal 2 carbon unit. We thought that if we could express FabH2 together with the PetroBrick, we could make even chain length alkanes. Ww cloned FabH2 into a alc inducible promoter to form [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590064 the FabBrick], an add-on module to teh PetroBrick system. The FabBrick was co-transformed with [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590025  the PetroBrick] in XL1-Blue ''E. coli''. cells were grown up in rich TB media+ 5uM IPTG, and innocultated to OD10 in M9 production media + 5uM IPTG. Alkanes were extracted after 24 hours. In addition, GC runs were performed on uninduced FabH2/PetroBrick cultures, and on cells expressing only [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590025  the PetroBrick].
 +
 
 +
There was no significant difference between the GC peaks in [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590025  the PetroBrick] extract and in the uninduced FabH2/PetroBrick Extract. All of the peaks in these two extracts that fall within the expected elution time of the C16 alkane( 9.5-10 min) correspond to trace amounts of compounds that we cannot identify. When the FabBrick is induced, we see a new peak at approximetly 9.75 minutes. The MS spectra of this peak is highly consistent with C16 alkane. The overall ion fragmentation fingerprint is identical to that of alkane. Identification as a C16 alkane is confirmed by the presence of a strong parent ion at a mass of 226, exactly the mass of the C16 alkane. This confirms production of C16 alkane. In addition, some C14 alkane production was observed. This is the first time that even chain length alkanes have been produced recombinantly, and expands [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590025  the PetroBrick] system to be able to produce all of the alkanes in the range C13-C17. Note that this peak corresponds to only trace levels of alkane( approximately 4mg/L), and future optimization is needed to increase even chain length production levels. The FabBrick system shows the modularity and expandability of the PetroBrick system, and is a first proof of concept of the expansion of PetroBricks to produce a wider range of products.  For more information on FabH2, refer to our [https://2011.igem.org/Team:Washington/Alkanes/Future/FabH2 future directions page ].
 +
 
 +
[[Image:FabBrickGCMS.png|left|400px|thumb|GCMS  trace confirming C16 alkane produced only upon FabBrick induction. ]]
 +
 
 +
 
 +
 
 +
 
 +
[[Image:FabBrickSpectrum.png|middle|400px|thumb|MS spectrum verifies peak contains C16 alkane. ]]

Latest revision as of 00:38, 29 October 2011


Diesel Production: Results Summary


GCMS confirms The PetroBrick enables diesel production from sugar using E. coli

We performed GC-MS analysis on extracts from cell cultures expressing both [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590032 Acyl-ACP Reductase] (AAR) and [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590031 Aldehyde Decarbonylase] (ADC) (this composite part is designated [http://partsregistry.org/Part:BBa_K590025 The PetroBrick]). To act as controls and in order to show that the alkane production system is working as expected, we also analyzed cell cultures expressing either only AAR, or only ADC.


Washington PetroBrick.png
GCMS confirms PetroBrick diesel production from sugar using E. coli


No significant hydrocarbons peaks in samples extracted from cells expressing only ADC. The blue GCMS chromatagram trace on the bottom show no significant peaks are found on the ADC only control within the time range that we expect alkane signal based upon GC-MS runs on chemical standards (8-10.5 minutes). This is expected, as E. coli does not normally produce any long chain length aldehyde substrates.

C16 alcohols are observed when AAR is expressed on its own. The red GCMS chromatagram trace in the middle has a significant peak at 10.2 minutes corresponding to the C16 alcohol (as confirmed by comparison of the peak's MS spectra to a reference library) is observed when AAR is expressed in MG1655 E. coli. The production of C16 alcohols in cells expressing AAR (but not in cells expressing only ADC) is consistent with AAR reducing even chain length Acyl-ACPs into even chain length fatty aldehydes, which are further reduced by aldehyde dehydrogenases to the alcohol.

The PetroBrick Works! C13, C15, and C17 alkanes are produced when both AAR and ADC are expressed.

Comparasion of the NIST reference C15 alkane spectrum( in blue) to the C15 peak spectrum taken from a PetroBrick culture (in red). Note the strong m/z peak at 212, corresponding to the parent ion of the C15 alkane. For spectra of the C13 alkane and C17 alkene, refer to our Spectra Page.

The green GCMS chromatagram trace in the middle has a significant new peaks corresponding to the C13 (8.2min) and C15 (9.2min) alkanes, as well as a peak at 10.2 minutes that contains both the C14 alcohol and the C17 alkene. The fact that the C17 alkene peak overlaps with the C14 alcohol peak makes exact quantification of C17 akene yields impossible, but we have sufficient evidence to determine that both molecules are present in the 10.2 minute peak( the earlier section of the peak has an MS spectra consistent with the C16 alcohol, and the later section is consistent with the C17 alkene). The C13 and C15 alkane peaks showed MS spectra highly consistent with C13 and C15 alkane reference spectra(for these spectra, as well as the C17 alkene spectrum, refer to our Spectra Page.). In addition, both alkane molecules eluted off of the GC at the same time as C13 and C15 alkane standards, further increasing confidence that the 8.2 min and 9.2 min peaks do correspond to the C13 and C15 alkanes. Odd chain length alkane production is what is expected from our system, as ADC removes a carbonyl group from even chain length aldehydes produced by AAR, yielding an odd chain length alkane. Using the PetroBrick, we can turn simple sugars into diesel, a fuel fully compatible with modern infrastructure.



Initial Quantization of Alkane Production

In order to be able to know how much alkane was being produced by our E. coli, we spiked known amounts of alkane into cell cultures known to not produce alkanes. We then extracted using ethyl acetate, and analyzed extracts using GC-MS. Since peak area corresponds to the amount of each substance present, we used these GC plots to make a standard curve that allows us to convert peak area into an absolute yield. To determine how much alkane was being produced by the Petrobrick, we grew up 3 MG1655 cell cultures transformed with the PetroBrick in M9 production media (link), and analyzed using GC-MS.

Standard curves for converting peak area to an absolute amount. Note that these curves is almost perfectly linear. In addition, the curve generated from each alkane is nearly identical, allowing us to use 1, average curve for all 3 different alkanes.
Diagram showing yields of the C13 and C15 alkanes. Note: The C17 alkene is not included due to inability to quantify.




Optimized Production

By optimizing the method of growth, media, vectors, and cell line we were able to successfully increase alkane yield over 80-fold. Note that this improvement doesn't include C17 alkene production, as we were unable to quantify the C17 alkene peak due to co-elution with the C14 alcohol. The parameters we adjusted for optimization are discussed in detail at our systems optimization page under future directions, as this is an on going process.

Our optimized growth conditions resulted in an 80 fold increase in total alkane yield.

The FabBrick, a module for even chain length alkane production

In order to more closely match the composition of diesel, we wanted a way to make the C14 and C16 alkanes, something that has never been reported before in the literature. For a detailed account of how we achieved this please see our future directions page. But a brief summary of our results is as follows:

We found an enzyme, FabH2 from Bacillus subtilis that has been hypothesized to start fatty acid biosynthesis with a 3 carbon unit instead of the normal 2 carbon unit. We thought that if we could express FabH2 together with the PetroBrick, we could make even chain length alkanes. Ww cloned FabH2 into a alc inducible promoter to form [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590064 the FabBrick], an add-on module to teh PetroBrick system. The FabBrick was co-transformed with [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590025 the PetroBrick] in XL1-Blue E. coli. cells were grown up in rich TB media+ 5uM IPTG, and innocultated to OD10 in M9 production media + 5uM IPTG. Alkanes were extracted after 24 hours. In addition, GC runs were performed on uninduced FabH2/PetroBrick cultures, and on cells expressing only [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590025 the PetroBrick].

There was no significant difference between the GC peaks in [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590025 the PetroBrick] extract and in the uninduced FabH2/PetroBrick Extract. All of the peaks in these two extracts that fall within the expected elution time of the C16 alkane( 9.5-10 min) correspond to trace amounts of compounds that we cannot identify. When the FabBrick is induced, we see a new peak at approximetly 9.75 minutes. The MS spectra of this peak is highly consistent with C16 alkane. The overall ion fragmentation fingerprint is identical to that of alkane. Identification as a C16 alkane is confirmed by the presence of a strong parent ion at a mass of 226, exactly the mass of the C16 alkane. This confirms production of C16 alkane. In addition, some C14 alkane production was observed. This is the first time that even chain length alkanes have been produced recombinantly, and expands [http://partsregistry.org/wiki/index.php?title=Part:BBa_K590025 the PetroBrick] system to be able to produce all of the alkanes in the range C13-C17. Note that this peak corresponds to only trace levels of alkane( approximately 4mg/L), and future optimization is needed to increase even chain length production levels. The FabBrick system shows the modularity and expandability of the PetroBrick system, and is a first proof of concept of the expansion of PetroBricks to produce a wider range of products. For more information on FabH2, refer to our future directions page .

GCMS trace confirming C16 alkane produced only upon FabBrick induction.



MS spectrum verifies peak contains C16 alkane.