Team:Edinburgh/Experiments

From 2011.igem.org

(Difference between revisions)
Line 7: Line 7:
<p class="h1">Results</p>
<p class="h1">Results</p>
-
Actual results of experiments are placed here.
+
Actual results of experiments are placed here, but more detailed discussions are also found on the relevant Registry pages.
==malS==
==malS==

Revision as of 18:05, 10 September 2011

Results

Actual results of experiments are placed here, but more detailed discussions are also found on the relevant Registry pages.

Contents

malS

We placed malS (an E. coli amylase gene) under the control of the lac promoter and grew the cells on starch agar. An iodine-based assay was carried out testing for starch degradation.

523001-assay-pre2.jpg     523001-assay-post.jpg     523001-assay-post-post2.jpg
Before the assay. Colony 1 failed to grow. Control at top.     Immediately after iodine flooding.     30 minutes after iodine flooding.

For more information, see the Registry page on <partinfo>BBa_K523001</partinfo>.

INP-EYFP

Edinburgh-INP-YFP-cells.jpg

We made a fusion (<partinfo>BBa_K523013</partinfo>) of Ice Nucleation Protein and Enhanced Yellow Fluorescent Protein, and placed it under the control of the Lac promoter.

Under blue light, the cells fluoresced yellow, as shown on right. Unfortunately, our imaging technology was not capable of showing whether the fluorescence was localised to the outer membrane.

BioSandwich tests

The BioSandwich system is outlined on its own page. BioSandwich creates parts with homologous ends, but there are a number of ways in which the final assembly could be carried out. We have tested a number of final assembly methods, by attempting to join a promoter and LacZ construct to a Yellow Fluorescent coding sequence. If successful, this will produce a polycistronic RNA transcript, coding for proteins that turn the bacteria blue (on Xgal) but also make it fluoresce yellow.

BioSandwich inserts short spacers between each part to be assembled. Note that after spacer2 we expect to see some extra bases before we reach the RFC10 suffix, because of the choice of vector. We can call these extra bases the "stuffing". So, the expected sequence is:

Vector -- spacerT7 -- Plac,LacZ -- spacer1 -- EYFP -- spacer2 -- stuffing

Successful assemblies are expected to generate blue colonies that fluoresce yellow under a blue light. We tried several assembly methods, all of which generated many colonies with the correct phenotype, but also many colonies with an incorrect phenotype...

From each plate we sequenced a colony with the correct phenotype (if there were any) and some colonies with incorrect phenotypes, in an attempt to understand what the failure modes were.

BioSandwich with Gibson Assembly

Like, OEPCR, this method produces many correct colonies and many incorrect colonies.

The Gibson method was described by [http://www.nature.com/nmeth/journal/v6/n5/full/nmeth.1318.html Gibson et al (2009)]. A gentle introduction was written by the 2010 Cambridge iGEM team, and is found here.

We sequenced a colony with the correct phenotype, as well as others with incorrect phenotypes:

  • Colony "gby" [blue, yellow] - expected scar is missing at approx base 680 of the forward chromatogram. Also, the spacer ends with ATG and the part starts with ATG, but only one ATG is seen. In total 9 bases are missing. There is homology of "tatgg" at both ends of the deleted fragment. There is a point mutation at approx base 500 of the forward chromatogram.
  • Colony "gb" [blue] - there is a deletion of about 80 bases at approx base 700 of the chromatogram. This has been caused by homology of a "gggcgagg" found at both ends of the deleted sequence. The 9 bases mentioned for gby are also missing.
  • Colony "gwy" [yellow] - seems correct except for a point mutation in the reverse chromatogram. The mutation is synonymous (ctg -> ttg). There's no clear reason why the colony wasn't blue.

Lessons learned: bits of homology, even quite small, can cause problems with this method.

BioSandwich with Overlap Extension PCR

Overlap Extension PCR can be performed using spoligos as primers. The extension time should be calculated from the entire product size. The final product will not be circular, so can be run on a gel to test its length. Later, it will need to have its ends ligated.

This method produces many correct colonies, although it also produces many incorrect colonies.

[For our tests, different primers were used and spacer2 was not needed.]

  • Colony "bby" [blue, yellow] - correct sequence.
  • Colony "bb" [blue] - has a massive deletion (several hundred bases) in the EYFP gene after about 60 bases. There is partial homology between the start and end of the deletion: "tggtcgagctggac" vs "tggacgagctgtac".
  • Colony "bw" [plain] - has spacerT7 joined to spacer1, and the same massive deletion as bb.

Again homology seems to be an issue. Parts joining randomly (in bw) is worrying.

BioSandwich with Ligation Independent Cloning

In our experience, this method has been only weakly successful. We have seen one correct colony in several attempts.

To attempt the LIC method, simply mix the parts and vector (4 uL of each). Heat a beaker of water to 95 C, and float the reaction tube in it, and allow everything to cool. Afterwards, it may now be necessary to centrifuge the tube briefly to move the liquid back to the bottom.

  • Colony "b1" [blue, yellow] - sequence read is of low quality but things seem correct.
  • Colony "y2" [yellow] - appears to simply be <partinfo>BBa_K216011</partinfo>, the template for the initial PCR
  • Colony "n4" [plain] - sequence is unreadable.

The y2 colony is probably expressing a template for PCR which made it all the way through the various steps that came afterwards.

BioSandwich with Blunt-End Ligation Independent Cloning

This is expected to fail as Ligation Independent Cloning requires long overhangs at the end of each part, not blunt ends. No correct colonies were seen.

  • Colony "bb1" [blue] - seems to be <partinfo>BBa_J33207</partinfo> followed by part of E. coli ferrous iron transport gene A.
  • Colony "bw2" [plain] - has spacerT7 followed by the stuffing.
  • Colony "bw3" [plain] - has RFC10 prefix followed by RFC10 suffix, as if XbaI and SpeI sites have joined in a normal vector.

BioSandwich with CPEC: Circular Polymerase Extension Cloning

  • Colony "cby" [blue, yellow] - there is a single-base deletion near the start of the PlacLacZ part, with no obvious cause. It is too early to affect expression. The last few bases of spacer1 are missing, as well as the first few bases of the EYFP part (9 bases total). This is explained by homology of "tatgg". Otherwise seems correct.
  • Colony "cb" [blue] - Normal until the end of spacer1, which is followed immediately by spacer2 and the stuffing.
  • Colony "cw" [plain] - spacerT7 is followed immediately by a second copy of spacerT7, after which comes spacer2 and a second copy of spacer2. Then the stuffing.

This gave some of the weirder results.