Designs overview

Introduction

Our goal for this summer is to characterize the travel of various molecules through nanotubes. In order to do so, we developed several designs. In this page, we explain the principle of the different designs we have built.

In the original paper [1], the authors directly observed the passage of molecules through the nanotubes. The idea behind our approach is to use synthetic biology methods to improve the sensitivity and the resolution of these experiments. Relying on signal amplification and natural, as well as artificial, bistable switches, we want to detect, with a resolution at the molecular level, the passage from one emitter cell to the receiver.

Main questions

The nanotube discovery is very recent. Lots of questions remain unsolved concerning the mechanism behind the formation of the tubes, the efficiency of the transfer, the extent of the process. The existence of the tubes themselves remains a subject of controversy within the scientific community.

We aim to bring additional proof of their existence and better characterize the extent of this phenomenon. Here is the list of the questions we have been asking ourselves, and that our designs aim to answer:

What is the nature of the process? (passive or active transport)
What kinds of molecules can pass through the nanotubes?
Does the communication happen only between B. subtilis? Or can it also exist between different species?
If a communication can be established with Gram negative bacteria, is the communication happening through the periplasm or the cytoplasm?

There is also the question of the formation of the tubes. However, this specific problem would require a lot more than a summer and a team of undergraduates to be fully investigated. We therefore choose not to focus too much on it, even though we have some ideas.

Specification of our designs

We started designing the project with these previously stated questions in mind. Using several molecules of different sizes and nature, from a T7 polymerase to ComS, we aim to test the nature, size and number limit of the molecules we try to pass through the nanotubes.

We decided that our constructs should follow the global idea summed up in the following scheme:

General plan for the experiment design to characterize the nanotubes

As explained in our modeling section, diffusion is supposed to be too quick comparatively to genetic networks response to be accurately measured. We therefore focused on testing the nature, the number and the size of the molecules we try to pass trough the nanotubes.

In B.subtilis, nanotubes are reported allow transfer to the cytoplasm. We had to find molecules that can be expressed in the first cell and then trigger a genetic circuit in the second cell. The image below illustrates the idea:

Schematic of the supposed connection between the cells via the nanotubes

ADD TABLE FOR MOLECULES SIZE AND NATURE

Building fast new genetic devices

Using these specifications, we designed several sensitive genetic circuits that can be trigerred by molecules of various sizes. The molecules chosen cover 2 orders of magnitude of radius. Here, they are classified from the biggest to the smallest.

	Description	Type of switch	B. subilis E. coli compatibility
	T7 polymerase diffusion: The T7 RNA polymerase is the RNA polymerase of the T7 phage. This is a big molecule, that recognizes a very specific promoter orthogonal to B.subtilis.	Irreversible amplification	Yes
	Amber suppressor tRNA diffusion: The principle of this design is to produce in one cell an amber supressor tRNA that will diffuse through the nanotubes. The receptor cell holds the gene for T7 with amber stop codons that cannot be translated into a functional protein as long as the tRNA amber suppressor is not present in the cell. Once expressed, the functional amber T7 RNA polymerase will trigger the T7 amplification system.	Irreversible amplification	Yes
	KinA diffusion: The Sin operon system controls the sporulation switch of B. subtilis. Making it diffuse from a non sporulating strain to a receiver cell makes the receiver cell to sporulate.	Switch	Mono- directional
Lambda switch	Lambda switch design: The CI is a regulation protein from the lambda phage switch. Make it diffuse would change the state of the toogle switch from the push-on push-off system, from the PKU 2007.	Switch	Mono- directional
	The YFP-TetR/TetO array experiment: This experiment is an improvement of the previous one. To observe significant fluorescence in the neighboring cells, lots of molecules have to pass through the tubes. Using the affinity of the TetR for the TetO array, we want to concentrate at one point the YFP molecules to better observe this diffusion.	-	Yes
	ComS diffusion: ComS is an inhibitor of the MecA protease in B.subtilis. It plays a key role in the triggering of the competence and sporulation mechanisms. The idea is to trigger the switch of the MeKS system of the receptor cell by diffusing ComS through the nanotubes. A major precaution is to prevent the first cell from sporulating.	Switch	Mono- directional

FEEDBACK FROM THE MODELS HERE

Others designs not built

We neither had time nor the manpower to try all the ideas we had. In particular, we have designed some systems in order to investigate the E. coli / B. subtilis connection nature. We had no time to investigate this question further. Nonetheless, we present some of our design ideas for solving this problem in this section.

B.subtilis is Gram- so the nanotubes seem to create a link from the cytoplasm of the first cell to the cytoplasm of the second cell. In the case of the Gram+ bacteria, like E.coli, we wonder which membrane forms the nanotubes . Do they create a link with the periplasm, or with the cytoplasm? To test the two hypotheses, we tried to create a design for each of the two possibilities. If one work and the other does not, the answer to this question will be known.

Design for B.subtilis / E. coli if the connection happens with the cytoplasm

If the connection between E. coli and B. subtilis is happening through the cytoplasm, the type of connection could be summed up by the following schematic.

Schematics of the communication happening directly to the cytoplasm

In this case, be can re-use most of the designs of the first section (see the compatibility column). We also have proposed this design:

Xis protein diffusion: Xis is a small partner of an excisase. The latter will excise a stop codon on the DNA strand that is preventing the expression of the GFP. We had no time to build this design, but the idea is summed up on the linked page.

Design for B.subtilis / E. coli if the connection happens with the periplasm

In case the communication happens with the periplasm, we have to think about molecules that can be then transported into the cytoplasm.

Schematic of the communication happening through the periplasm.

We had to design more sophisticated approaches. The ideas are the following:

MBP diffusion: we need a CRP+, MBP- E.coli mutant. We produce the MBP protein in B.subtilis and make it diffuse through the nanotubes. As long as the MBP has not reached the periplasm of E.coli, the cell cannot digest the maltose in the medium. The indirect induction of MalR by MBP triggers the expression of the GFP reporter.

References