"
Team:Copenhagen/Protocol
| You can write a background of your team here. Give us a background of your team, the members, etc. Or tell us more about something of your choosing. |  |
|
Tell us more about your project. Give us background. Use this is the abstract of your project. Be descriptive but concise (1-2 paragraphs) |  Your team picture |
| Team Example |
| Home | Team | Official Team Profile | Project | Parts Submitted to the Registry | Notebook | Safety | Attributions |
|---|
Contents |
Protocols
First Week 22-24 of June
Mutations
Ingredients
Site directed mutagenesis of 3 plant CYP450 (79A1, 79A2, 79B1).
We aim to destroy restrictionenzymes recognitionsites.
Primers was supplied by ...........
10 μl of 5× reaction buffer
X μl (50 ng) of dsDNA template
X μl (125 ng) of oligonucleotide primer #1
X μl (125 ng) of oligonucleotide primer #2
1 μl of dNTP mix
ddH2O to a final volume of 50 μl
Then add
1 μl of X7 fusion DNA polymerase
Poly Chain Reaction
We ran a PCR to syntesise and amplify our mutated CYP's.
Cycling Parameters for the QuikChange Site-Directed Mutagenesis Method
Cycles 12
Temperature 98°C Time 30 seconds
Temperature 55°C Time 1 minute
Temperature 72°C Time 30 seconds/kb of plasmid length
Digestion
We aim to remove the parentel CYP.
We take advantage of the fact that this CYP is methylated on cytosines. Dpn is a restriction enzyme that cuts DNA which is methylated - therefore our new mutated CYPs remain untouched.
1. Add 1 μl of the Dpn I restriction enzyme (10 U/μl) directly to each amplification reaction.
2. Gently and thoroughly mix each reaction mixture by pipetting the solution up and down several times. Spin down the reaction mixtures in a microcentrifuge for 1 minute and immediately incubate each reaction at 37°C (in a heater with lid or in a 37°C room) for 1 hour to digest the parental (i.e., the nonmutated) supercoiled dsDNA.
Source
Adapted from QuikChange™ Site-Directed Mutagenesis Kit INSTRUCTION MANUAL
Competent Cells
E. coli Calcium Chloride competent cell protocol
1. Inoculate a single colony into 5mL Lb in 15mL falcon tube. Grow O/N at 37°C.
2. Use 1mL to inoculate 100mL of LB in 250mL bottle the next morning.
3. Shake at 37°C for 1.5-3hrs until OD600 = 0.4-0.8
Then…. 1. Put the cells on ice for 10 mins (keep cold form now on).
2. Collect the cells by centrifugation in the big centrifugue for 10 mins at 6krpm
3. Decant supernatant and gently resuspend on 10 mL cold 0.1M CaCl (cells are susceptible to mechanical disruption, so treat them nicely).
4. Incubate on ice x 20 mins
5. Centrifuge as in 2
6. Discard supernatant and gently resuspend on 5mL cold 0.1MCaCl/15%Glycerol (from a 85% stock)
7. Dispense in microtubes (300μL/tube). Freeze in -80°C.
Source:
Adapted from http://www.med.nyu.edu/medicine/labs/blaserlab/Protocols/E-coli_competent_cells_protocol_&_transformation.pdf
LBamp Plates
1. 500 ml LB agar and 500 μL amphicilin 2. Pour on plates 3. Leave with the lid half on for 30 minutes at room temperature 4. Put in refrigerator until needed.
Transformations
Transformation of Ca++ competent cells
1. Put ~50μL of competent cells to prechilled microtubes. Wait 1 minute. Add 10μL of circular plasmid or all of a ligation reaction of plasmid DNA.
2. Incubate for 30 mins on ice.
3. Heat shock for 45 seconds at 42°C. Put back on ice.
4. Plate the whole lot in LBamp plates
5. Leave the plates at 37°C O/N
Second Week
Mini prep
Ingredients
QIAprep® Spin Miniprep Kit
- Buffer P1 (with LyseBlue)
- Buffer P2 - Lysis Buffer
- Buffer N3 - Neutralisation buffer
- Buffer PB - Binding buffer
- Buffer PE - Wash Buffer
- Buffer EB - Elution Buffer
- 5 ml bacterial overnight culture transformed with our BioBrick
Miniprep
1. Pellet 5 ml bacterial overnight culture by centrifugation at 4500 rpm for 10 min at room temperature (20°C).
2. Resuspend pelleted bacterial cells in 500 μl Buffer P1 and transfer and divide in two microcentrifuge tubes.
3. Add 250 μl Buffer P2 to each tube and mix thoroughly by inverting the tube 4–6 times until the solution becomes blue. Do not allow the lysis reaction to proceed for more than 5 min.
4. Add to each 350 μl Buffer N3 and mix immediately and thoroughly by inverting the tube 4–6 times. With LyseBlue reagent, the solution will turn colorless.
5. Centrifuge for 10 min at 13,000 rpm (~17,900 x g) in a table-top microcentrifuge.
6. Apply the supernatant from step 5 to the QIAprep spin column by decanting or pipetting. Centrifuge for 60 s and discard the flow-through.
7. Wash the QIAprep spin column by adding 0.5 ml Buffer PB. Centrifuge for 60 s and discard the flow-through
8. Wash the QIAprep spin column by adding 0.75 ml Buffer PE. Centrifuge for 60 s and discard the flow-through, Transfer the QIAprep spin column to the collection tube.
9. Centrifuge for 1 min to remove residual wash buffer.
10. Place the QIAprep column in a clean 1.5 ml microcentrifuge tube. To elute DNA, add 50 μl Buffer EB (10 mM Tris·Cl, pH 8.5) to the center of the QIAprep spin column, let stand for 1 min, and centrifuge for 1 min.
Adapted from
Quick-StartProtocol QIAprep® Spin Miniprep Kit October 2010 [http://www.qiagen.com/literature/render.aspx?id=201081]
Third Week
Fourth Week
You should make use of the calendar feature on the wiki and start a lab notebook. This may be looked at by the judges to see how your work progressed throughout the summer. It is a very useful organizational tool as well.
