"
Team:EPF-Lausanne/Protocols
From 2011.igem.org
| Line 70: | Line 70: | ||
<p>• incubate TF with target DNA at RT for 30-60 minutes (to reach a thermodynamic equilibrium)</p> | <p>• incubate TF with target DNA at RT for 30-60 minutes (to reach a thermodynamic equilibrium)</p> | ||
<p>• scan using Arrayworx</p> | <p>• scan using Arrayworx</p> | ||
| + | <p> Use 1 sec exposure time</p> | ||
<p>• close button</p> | <p>• close button</p> | ||
<p>• close chamber</p> | <p>• close chamber</p> | ||
Revision as of 16:08, 16 May 2011
PDMS two layer device fabrication
made on 16.05.2011
Materials:
• flow and control layer molds
• Sylgard 184 silicone elastomer kit: Base part and a Curing agent
• TMCS
Method:
• Place molds into a TMCS vapor chamber
• Control layer mixture: 20g Base + 4g Curing agent
• Mix for 1 minute, degas for 2 minutes (standard protocol)
• pour onto control layer mold and place mold in vacuum chamber
• Flow layer mixture: 20g Base + 1g Curing agent
• Mix for 1 minute and degas for 2 minutes (standard protocol)
• Spin coat onto flow layer at 2200-2400rpm for 35secs (so far you can use my protocol on a spin coater)
• Remove control layer mold from vacuum chamber, making sure no bubbles are left on the surface (remove with a toothpick if you see some )
• Place the control and flow layer in a 80C convection oven and incubate for 30 minutes (timing is critical here!)
• Remove casts from oven, cut out control layer, punch holes, and align to flow layer
• Put aligned device back into 80C oven and incubate for at least 90 minutes (and here you can increase the backing time)
• Remove devices from oven and punch flow layer holes
</div>
MITOMI: Protein – DNA interactions
made on 16.05.2011
Purpose:
To detect potential protein-DNA interactions
Chip:
MITOMI device bonded to epoxy slide spotted with DNA samples, bonded at 40C overnight (alternatively @room temperature)
Method:
• Load all control lines with dH2O, at ~5 psi, check that all valves work
Usually “B” valves are starting to load earlier (leave the button unpressurised prior to the pressure increase, it tends to stick to the slide.)
Increase the pressure in both “A” and “B” valves till ~13-15 psi and make sure that you can see that all chambers are separated. If no – increase the pressure
• 2mg/ml BSA-bio @ 5psi for 20 minutes; chambers (B3): closed
• You can prepare the ITT mix meanwhile and put it at 25C for 3-4 hours (it takes that long to express your TF with a GFP tag)
• PBS for ~2 minutes (or as long as the preparation for next step takes)
• 500ug/ml NA PBS for 20 minutes
• PBS for ~5 minutes
• Close button, continue PBS for 1-2minutes making sure button is closedv <p>• 2mg/ml BSA biotin for 20 minutes
• PBS for 10 minutes
• Antibody-GFP-biotin in PBS for 4-5 minutes
• open button, continue antibody for 20 minutes
• PBS for ~10 minutes
• flow the expression mix with expressed protein for 10-15 minutes, when ~2-3 cm of mix left in the inlet tube :
• Close outlet B4 and open B3 (isolates spotted DNA in a chamber) and load chambers with the same expression mix
To do so you should close the outlet first (“B4”) and continue flow. Stop the flow as soon as all your chambers with DNA will be filled. Do not wait for too long or DNA will diffuse to the neighbor chamber
• close chambers
• close sandwich
• open chamber
• incubate TF with target DNA at RT for 30-60 minutes (to reach a thermodynamic equilibrium)
• scan using Arrayworx
Use 1 sec exposure time
• close button
• close chamber
• open sandwich
• PBS for 10-15 minutes
• scan using Arrayworx to detect the interacting sequences
