Team:EPF-Lausanne/Notebook/June2011

From 2011.igem.org

(Difference between revisions)
(→Gibson Assembly)
 
(13 intermediate revisions not shown)
Line 200: Line 200:
Henrike and Irina designed primers for both plasmids, with the goal of amplifying the following four parts:
Henrike and Irina designed primers for both plasmids, with the goal of amplifying the following four parts:
 +
 +
1) a pTet-RFP segment (820 bp)
1) a pTet-RFP segment (820 bp)
 +
*Primer 1: J61002-Ptet-RFP-r
 +
*Primer 2: J61002-RFP-f
 +
*DNA template: Plate 1, 18 C
 +
2) a J61002 plasmid backbone with a terminator (2334 bp)
2) a J61002 plasmid backbone with a terminator (2334 bp)
 +
*Primer 1: J61002-f
 +
*Primer 2: J61002-term-r
 +
*DNA template: Plate 1, 18 C
 +
3) a constitutive promoter for TetR (725 bp)  
3) a constitutive promoter for TetR (725 bp)  
 +
*Primer 1: Pconst-tetR-f
 +
*Primer 2: TetR-r
 +
*DNA template: TetR Repressilator plasmid
 +
4) P23019 plasmid (2242 bp)
4) P23019 plasmid (2242 bp)
 +
*Primer 1: P23019-r
 +
*Primer 2: P23019-f
 +
*DNA template: Plate 4, 14E
With a first PCR, we were able to amplify the pTet-RFP segment and the promoter for TetR, but neither of the backbones was amplified. The iProof PCR was done using 40 seconds of elongation time at 55 C.  
With a first PCR, we were able to amplify the pTet-RFP segment and the promoter for TetR, but neither of the backbones was amplified. The iProof PCR was done using 40 seconds of elongation time at 55 C.  
-
[[File:EPFL_28-06-firstpcr.tif‎|300px|TetR fluorescence during target DNA experiment]]
+
[[File:EPFL-28-06-pcr.jpg‎|300px|TetR segment and RFP-pTet segment amplified. Both backbones unamplified]]
== Wednesday, 29 June 2011 ==
== Wednesday, 29 June 2011 ==
 +
The mixed success of the previous day's PCR required a change in tactics. First, it was decided that the elongation time should be increased from 40 seconds to 1 minute. Second, it was deemed important to take melting temperature into consideration. The IDT (Integrated DNA Technologies) toolbox allows you to compute melting temperatures for sequences. Inserting the primer sequences yielded the following heats:
 +
 +
1) P23019-r: 45.8 + 3 = 48.8
 +
 +
2) P23019-f: 60.8 + 3 = 63.8
 +
 +
3) J61002-bb-f: 52.2 + 3 = 55.2
 +
 +
4) J61002-term-r: 49.3 + 3 = 52.3
 +
 +
 +
The lowest temperature was 49 (48.8) so we proceeded to do a PCR with these values. The J61002 plasmid backbone was properly amplified.However, the P23019 backbone remained unamplified despite these changes.
 +
 +
[[File:EPFL-29-06_J6_backb.jpg|300px|J61002 backbone amplification, but no P23019]]
== Thursday, 30 June 2011 ==
== Thursday, 30 June 2011 ==
Line 227: Line 258:
 +
== Gibson Assembly==
 +
 +
 +
On the Gibson assembly side of things, Vincent and Irina purified the PCR product of both the J61002 plasmid and the pTet-RFP construct using the standard PCR purification protocol. Then, using NanoDrop, they measured the concentrations of J61002 plasmid and of the RFP construct:
 +
 +
 +
RFP (820 bp) : 28.8 ng/microL
 +
 +
 +
J6 (2334 bp) : 26 ng/microL
 +
 +
 +
'''Instead of following the instructions on the wiki by Nikolaus Obholzer which has the wrong formula for finding the equal molecular ratio''', we determined that the ratio ought to be 80/233 since the length of the RFP fragment is 820 bp and the length of the J6 plasmid is 2334. To make the Gibson mix, we used 2.6 microliters (80 ng % 28.8 ng/microL) of the RFP segment and 9 microliters of the plasmid (230 ng % 26 ng/microL). The assembly was done with a sample of 5 microliters taken from the 11.6 microliter mix.
 +
 +
We then did a transformation with these Gibson-ed plasmids and plated the cells on ampicillin plates and put them in the incubator overnight.
 +
 +
==  Gradient PCR  ==
 +
In a last attempt to try to amplify the P23019 plasmid backbone (the last piece needed to start a Gibson assembly of the TetR plasmid), Vincent tried a gradient PCR in which separate samples of the plasmid would be run at temperatures between 40 and 50 C (40, 42, 44, 46, and 48). The results showed, once again, that amplification was beyond reach.
 +
[[File:EPFL-29-06-p23019fail.jpg|300px|GFP-tetR and cy5 fluorescence]]
{{:Team:EPF-Lausanne/Templates/Footer}}
{{:Team:EPF-Lausanne/Templates/Footer}}

Latest revision as of 16:51, 9 July 2011

Retrieved from "http://2011.igem.org/Team:EPF-Lausanne/Notebook/June2011"