Team:Cornell/Results

From 2011.igem.org

(Difference between revisions)
(Light-Induced Lysis)
Line 83: Line 83:
=Light-Induced Lysis=
=Light-Induced Lysis=
</font>
</font>
 +
We designed the light-induced apoptosis system using APE and submitted the part to Invitrogen Life Technologies for synthesis. Given our final construct was in excess of 6,000 bp, synthesis is currently being performed into two subsections. The first of which is the light sensitive promoter (Pcpcg2) followed by the lysis cassette and the genes neccesary for the biosynthesis of phytocyclobillins. The second component was the CCaS and CCaR. CCaS is the surface 532 nm green light activated protein which phosphorylates, and activates, CCaR to bind to the light sensitive promoter and express the downstream gene.
 +
 +
    We have received so far the second component of our light system and have biobricked this part for submission and use with the international parts registry. Please see http://partsregistry.org/wiki/index.php?title=Part:BBa_K597105 for a further description

Revision as of 03:40, 29 September 2011

Results | Protocol | Notebook | Parts Submitted

Contents

Enzymatic Pathway

Through the summer, we successfully constructed the tagged violacein pathway enzymes VioA, VioB, VioE and submitted those parts to the registry. These three enzymes in series are capable of converting L-tryptophan into prodeoxyviolacein, a dark green colored intermediate of the violacein pathway. Each enzyme sequence was constructed to have the Avi-tag sequence included on its C-terminus, followed by the stop codon so that one single fusion protein is expressed. The avitag is capable of biotinylating the enzymes so that they could be bound to surfaces using a simple NeturAvidin ligand system.

To simplify the construction process, each enzyme sequence was PCR'd off the iGEM Distribution sample with a KpnI site followed by the iGEM prefix, the gene of interest, and ended with an SphI or HindIII site that replaced the location of the stop codon. These PCR products could then be ligated into a modified pZE12-SMCS backbone which contained the Avitag sequence followed by the stop codon, iGEM suffix and ClaI site. This backbone was constructed using the primer insert method outlined in the Project Description.

With the modified enzymes, we performed experiments to show their expression and utilization of tryptophan using a UV/Vis spectrometer at the peak wavelengths at which tryptophan responds to (590,638, and 562 nm). The OD measurements of solutions containing equivolume of VioA, VioB, 40 mM Hydrogen Peroxide (for oxidation of tryptophan) and VioE lysate with varying concentration of tryptophan. The results are shown below.

Graph-Tryptophan,Vioenzymes Cornell2011.jpg

The green points represent readings at 562 nm, blue at 590 nm, and red at 638 nm at 0.008 g/mL concentration of L-Tryptophan and 40 mM H202. As you can see, the absorbance of tryptophan noticably decreases over a time course of 1 hour. This experiment was recreated varying the ratio of enzymes and concentration of initial tryptophan. The results showed a similar decreasing trend.

Control.jpg

This is the control tryptophan readings. In the absence of violacein enzymes, the amount of tryptophan showed the opposite trend.

Microfluidics Assembly

Binding Experiment

Goal- to determine if the biotinylated enzymes would attach to the streptavidin coated wall.

Experiment

  • Negative Control- chip that is not coated with strepavidin through which we flowed ATTO 590.
  • Test- streptavidin coated chip through which we flowed ATTO 590.
  • Flow Rate- 5ul/min
  • Run Time- 20min
After the experiment, air was flown through the chips and pictures were taken.

Results

The red fluorescence indicates that the enzyme successfully bound to the channel wall.

Lysate Experiment

Goal- to determine the effect lysate would have on the binding efficiency between the streptavidin coated walls and the biotinylated enzymes.

Experiment

  • Positive Control- streptavidin coated chip through which we flowed ATTO 520
  • Negative Control- uncoated chip through which we flowed ATTO 520
  • Test- streptavidin coated chip through which we flowed a 5:1 ratio of lysate to ATTO fdafdsfdfdsa 520.
  • Flow Rate = 5ul/min
  • Total Run Time = 30min
Entire setup was covered in aluminum foil and the lights were dimmed.

After the experiment, air was flown through the chips and pictures were taken. Channels were filled with DI water and stored in the 4 degree fridge wrapped in Al foil.

Results

The test chip showed a lower level of fluorescence compared to the positive control chip. This indicates that lysate has a small inhibitory effect on the binding between streptavidin and biotin.

Continuous Flow Experiment

Goal-to determine how long the attached enzymes would stay attached under continuous flow.

  • Negative Control- noncoated chip
  • Test- Flow DI water through a chip with ATTO 520 attached to the strepavidin coated PDMS for 15min.
  • Flow Rate = 200ul/min
  • Total Run Time = 45min, 3 15 min intervals
After each interval, the chip was washed with air and a picture was taken in air.

Results

The pictures indicate that the fluorescence gradually reduces under continuous flow. This suggests that the chips might have to be recoated after extended wear.

GFP biobrick

Goal- to determine if our Avi tagged GFP will bind to our streptavidin coated chip.

Experiment

  • Negative Control- A coated chip that is flushed with DI Water
  • Test- A chip coated with streptavidin with filtered GFP lysate flown through
  • Flow Rate- 5 ul/min
  • Total Run Time- 20min
The GFP containing cells were lysed with Bugbuster and filtered through a PD-10 Desalting Columns to remove excess biotin. Afterwards the chip was stored in DI Water in the fridge in aluminum foil. 4 days later we took the chip out and imaged it again. Then DI Water was flushed through and the chip was reimaged. It was seen that most of the binding occurred at the inlet port and the first channel. By the second channel there was no fluorescence found.

Results

The presence of green fluorescence shows that our biobrick successfully bound to the channel wall. Furthermore, green fluorescence was still present even after the chip was stored for 4 days in the fridge. However, the fluorescence after 4 days was significantly less than the initial fluorescence.

Light-Induced Lysis

We designed the light-induced apoptosis system using APE and submitted the part to Invitrogen Life Technologies for synthesis. Given our final construct was in excess of 6,000 bp, synthesis is currently being performed into two subsections. The first of which is the light sensitive promoter (Pcpcg2) followed by the lysis cassette and the genes neccesary for the biosynthesis of phytocyclobillins. The second component was the CCaS and CCaR. CCaS is the surface 532 nm green light activated protein which phosphorylates, and activates, CCaR to bind to the light sensitive promoter and express the downstream gene.

   We have received so far the second component of our light system and have biobricked this part for submission and use with the international parts registry. Please see http://partsregistry.org/wiki/index.php?title=Part:BBa_K597105 for a further description