Friday, August 26

From 2011.igem.org

Revision as of 09:35, 30 August 2011

Dr Liz working alone in lab on Friday

CAUTION - AS THE WIKI NOTES THAT I TYPE KEEP GETTING DELETED BY SOME INADVERTENT ACTION ON MY PART (WARNING - DON'T USE THE BACK BUTTON), I WILL BE SAVING THIS PAGE THROUGHOUT THE EDITING PROCESS, BECAUSE i CAN'T STAND THE IDEA OF $#@%! TYPING EVERYTHING FOR A fourth TIME TONIGHT!

The cell cultures in LB broth + amp that had been shaking in the incubator overnight were removed to the cold room about 5:00 pm. This amounted to about 17 hours, and we had set the incubator low - 31.5 degrees C. So I expect they were still in log growth phase.

Purification Protocol that includes Phenol:Chloroform Step

I used the Phage DNA purfication by lysis protocol from the Handbook of Molecular Cloning, Vol 1. Jessica has input this protocol on the wiki- I have not found it yet. Please link this page to the protocol if you can, somebody.

There are a couple of modifications and special points worth discussing about using this protocol, as opposed to using spin tubes in a kit.

First: Everything must be and was kept very cold. I even put a vortexer in the coldroom next to the microfuge. Hint: If you know you're going to be working in the cold room for any extended period of time, make sure you are wearing warm socks and shoes. I'd even recommend a wool hat. By the time I was done with these cold steps in the purification process, I felt like a human popsicle!

Second: The phenol:chloroform step of the purification process is labelled as optional. However, the authors of Handbook, as well as other molecular biologists who have posted information on the web about the phenol:chloroform extraction step seem to agree on the following point: Downstream reactions may not work as well if you do not do the phenol:chloroform step. In particular, restriction digestion steps may not work well. One solution to a slow restriction digestion is to simply overload the amount of the restriction enzyme in the reaction - as much as a 10-fold increase is used in cases requiring better results. According to NEB, this is a fairly standard procedure, when needed. As we live on donations, it seemed to make sense to just do the phenol chloroform step instead. More information, particularly safety information, about doing this step of the purification is found below in the "Phenol:Chloroform" section.

The Basic Purification By Lysis Protocol, using Solutions I, II and III

I began the purification by following the protocol mentioned above, taking a 1.5 ml aliquot from each cell culture sample (each originally contained ~3.0 ml), and putting the remainder back into the cold room. I used Solution I and II, already available in the fridge and freezer from earlier in the month. and mixed a fresh batch of Solution II, as recommended. I made roughly enough for the nine samples. As when mixing Solution II for the first time early in August, I used the 0.4 M NaOH stock solution that was available (as opposed to 10 M NaOH, which is recommended). The 10% SDS solution used today had been freshly made by Cheryl Brown within the last several weeks, and was a different batch than the SDS in the Solution II used when the same basic protocol was first used this summer -- to purify DNA from cell cultures seeded with single-colony clones picked from amp plates that had been innoculated with cells which had been transformed by plasmids containing one of P, R ot T -- the first 3 BioBrick parts our 2011 iGEM Team extracted from the Parts Plates.

An interesting observation was that there appeared to be significantly more of cellular material in the bottoms of all of the 3B tubes compared to the 4A tubes after the initial spin down. The same observation persisted after the addition of the 3 solutions, the vortexing and the accompanying spindown that pelleted the DNA.

The next step was the phenol:chlorofrm step, which we will postpone just long enough to finish discussing the other, last steps in the purification protocol. The last steps are DNA precipitation by the addition of at least 2.5 volumes of ice-cold 95% ethanol. The DNA precipitation with 95% ethanol would normally be followed by a spin-down to form the DNA pellet in the bottom of the tube (It's actually the salts that you are seeing), and a pouring off of the supernatant, which should be free of plasmid DNA. I had a moment of some doubt when I did not see the DNA precipitate when I added the ice-cod 95% ethanol. Further, the spin down step did not produce a clearly visible pellet of DNA at the bottom of each tube. I saw more of what appeared to be a colorless, almost grainy-looking sludge on the wall a the bottom of the tube where one would normally find the pellet. Now there seem to be a couple of opposing possibilities here. Perhaps my DNA got SO clean during the phenol:chloroform step that the pellet is hardly visible because it is relatively free of salts. The other possibility might be that I did not add enough ethanol to precipitate the DNA out of the quantity of solution that I had in the tube.

Saving certain byproducts that are normally discarded as a failsafe measure

Because of this doubt I employed a failsafe procedure that you might always consider doing if you are not certain that your work is going as it should. Namely, after the addition of 95% ethanol for precipitating the DNA and cetrifuging the samples to pellet the DNA, I saved the supernatant that would normally be poured off and discarded.For these particular samples, they are labeled with the corresponding tube's name, followed by the "prime" symbol, which is just a single apostrophe " ' ".

I finished the procedure by performing the last step - adding 70% ethanol as a wash, and again, discarding the supernatant. I tried to be very careful not to wick away any of the clear "sludge"-like material that appeared in my tubes.

spin and almost all of the other centrifugation steps in this protocolare done in a microfuge at 12,000 rpm and 4 degrees C. The only exceptions are the spin downs during the phenol and chloroform steps, which are done at room temp, pouring off of the 95% ethanol while being mindfull of the DNA pellet, followed by a final wash with 70% ethanol and the accompanying final spindown and pouring off of this last ethanol wash, carefully avoiding accidently pouring away the often-loose pellet of DNA at the bottm of the tube. See the "Finding Your Pellet after Centrifugation" section below.

Growing up a cell culture seeded by a single colony from a cloned cell

After the P, R and T parts were eluted by Patrick and other team members, they were used to clone competent cells, which were then plated on agarose +amp plates. Single colonies were chosen from the plates after incubation, and were grown up in amp-rich LB broth in the warm shaker. One thing we have learned since then is that parafilm should not be used to secure the lids of these tubes, as they were specially designed for shaking a cell culture overnight - the idea is to get air in there. We were concerned about the culture sloshing out of the tubes, because the lids seemed loose. We understood only that air is required for cell growth, but thought sufficient air would be in the tube if we filled each tube with cell culture taking up no more than 1/3 of the tube's volume. This air deficit might explain some things, including why there was no DNA on gels run after purification of the plasmid DNA from those cell cultures. Is it possible that there was not ample air for these cells togrow and to manufacture lots of plasmids at the same time? Hard to say.

What we can say is we DID NOT make this error again when the 9 cell cultures were put in the incubator on Thursday night, August 25.