Reflectin Thin Films II

Thin films were produced after refining our earlier methods described in the experiment reflectin thin films I, during which we discovered some very interesting properties.

Practice

• Centrifugation of the solutions prior to coating to sediment insoluble impurities (13000rpm for 10 minutes). We hope to reduce the level of solid impurities.
• Introduction of liquid CO₂ pressure wash for cleaning of silicon substrates. O₂ plasma may have changed surface chemistry of the silicon, it is hoped physical cleaning will aid 'wetting' of the substrate providing a nice interface for subsequent coating.
• Trial spin coating on glass substrate to investigate the effect of different substrates and image of above and below lighting.
• Heat cured the thin films for varying amounts from couple of seconds to 30 minutes at 80^oc
• Measured the reflectance spectra of some of the thin films to check colouration
• BSA (Bovine Serum Albumin) control to assess generic properties of proteinaceous thin films subject to the same coating conditions.

Results

The result of centrifugation has led to dramatic differences in the spin-coated films. Below are shown typical results. The first image highlights the films produced on the first day whilst the second image highlights films produced using the refined protocol, finally the third image shows the BSA control produced using the refined protocol

Reflectin Thin Film made with protein/HFIP solution (not centrifuged

This film shows mainly dark spots suggesting diffuse scattering and therefore solid impurities and great variations in colour, which implies a variation in film thickness and confirmed when we imaged them under the confocal microscope.

Reflectin Thin Filmus made with centrifuged protein/HFIP solution

This film produced from the refined protocol demonstrates a much more uniform colour, dark blue in the bottom left fading to yellow in the top right. There are still numerous marks that suggest impurites or the possibility the films are not aggregating properly, but they are dominated by smooth blue and yellow regions.

Thin Film made with Bovine Serum Albumin/HFIP solution

The BSA control shows the films formed do not seem to demonstrate 'iridescence' than reflectin, though it does reflect a very discrete selection of wavelengths, mainly blue as opposed to the multicolours of reflectin films. There are however much less disruption in the form of impurities, most likely as the bovine serum albumin was purified industrially as opposed to the small scale methods we are implementing in the lab.

Further Observations and Conjecture

Source of Impurities

• The HFIP was centrifuged, no pellet/sediment was observed and the resulting spin-coat left only silicon substrate
• The resulting pellet from reflectin-HFIP centrifugation was suspended in HFIP. It was found to be mainly insoluble and subsequent coating did not yield a film with interference effects.
• The supernatant from reflectin-HFIP centrifugation was spin-coated and though the films were more uniform in colour careful examination yielded areas of film dissociation and black spots surrounded by interference rings much akin to newton's rings.

It is conjectured that purity of reflectin affects the quality of film produced, there may be soluble as well as insoluble contaminants, the source of which lies within the extracted protein.

Crystallization Behaviour

• The sample films were formed under different conditions with good samples repeated, some were spin-coated heat-treated and not heat-treated and some flow-coated heat treated and non-heat treated.
• It was found the majority of films made with 50μl centrifuged reflectin-HFIP were unstable, for some reason the films formed spontaneously crystallized stripping the films of its colour and leaving a colourless branching array of needle-like crystalline structures formed from the solution.
• All spindle-like structures seemed to nucleate at points where tweezers were used to pick them up and seemed to require this as a stimulus however some were fine but nucleated after a certain length of time.
• The effect seemed to relate to the size of the substrate with large(>4cm²) and small(<1cm²) substrates forming more quickly than medium sized substrates. Time lengths varied from immediately after coating to 1-2 days after to potentially never
• It was noted with one of the films which were subsequently heated at 80^oc for 30 mins after spin-coating, no nucleation ever occurred no matter how it was tampered with suggesting this treatment somehow prevents crystallisation possibly by promoting cross-linking or other mechanism for stabilisation of the thin-film.
• The phenomenon occurred with both flow coating and spin coating methods
• Interestingly different coating conditions and substrates produced spindle-like structures of different orientations and density. In one instance the structures formed were so dense it induced a band of iridescence orthogonal to spindle structures. Closer inspection reveals an intricate, regular inter-linked network of solution trapped between the spindles.
• We found that it was possible to induce further assembly of the needle like structures. Under the microscope it was seen that the solution first seemingly expanded before reforming into the crystal-like spindles.

• On application of D.I water onto the thin films under the optical microscope a dynamic play resulted between the formation of the spindle-like structure and the 'iridescent' thin film which oscillates back and forth, the spindle-like structure state becoming more favourable as the water droplet evaporated off the film.
• If the entire surface is re-hydrolysed on evaporation of the water droplet, a much more intense iridescent thin film is formed which upon re-heating at 80_oc induces re-formation of the spindle-like structures but less readily and slower with varying nucleation points almost as if it is nucleating around particular defects.
• Interestingly after heat treatment dropping water onto the film seems to destroy the underlying film which does not happen without heat treating whilst breathing on it re-hydrolysed it without destruction.

Subjection of Films to Vapour

• Subjecting the film to water and ethanol vapour elicited a colour shift from blue to red in the EM spectrum. This was carried out using only the one sample where it retained its iridescence. This is in-line with thin-film interference and literature. The vapours induce swelling which leads to subsequent phase shifts in reflected wavelengths which exhibits itself as a colour shift.

Summary

• The BSA control illustrates proteins being themselves polymers can be cast into thin films with differing physical properties therefore conclusions made with reflectin may equally apply to other proteins. As the dominant composition of reflectin are the unusually high amounts of sulphur and aromatic compounds it is advisable to perform controls with similarly unusual proteins of similar composition.
• Self-assembly crystallization behaviour is due to dehydration of films, subsequent application of water seemed to reverse the change whilst heating restored the crystallization albeit at a much slower speed than initially. This spontaneous phase separation requires further study in particular reproduction of the conditions under which it forms initially after spin/flow coating. However subsequent prolonged 'curing' seemingly stabilises the film. The crystallization may also be due to other factors like the amount of reflectin or presence of contaminants. Further investigations are required.
• Colour changes can be initiated by application of water and ethanol vapours consistent with thin-film interference and existing literature.

Proposed Routes for Further Investigation

Further investigations based on our preliminary results can be split into the following avenues:

• Colour Control - The application of vapour to control colouration changes has been confirmed. A natural progression is to replicate more closely the natural colouration mechanism in squid due to phosphorylation. We propose to investigate further by submerging films in bath of phosphate donors e.g phosphoric acid and electrical control via formation of an electrical 'cell'. Our ultimate aim is to the production of an electronically controlled pixel.
• Colour Intensity - In close tandem with the above point, at present the coloured films are not very bright, the formation of multi-layer reflectin-polymer layers is expected to improve the intensity of colours and reproduce more closely the observed 'bragg stacks' formed natively in squid iridophores. Though we have initially experimented with coating reflectin atop a flexible polymer, PDMS no serious experimentation were undertaken. It is proposed to take this to the next level with the aim of producing similar thickness layers via spin coating and increasing layers using a 'swiss roll' technique where a two-layer film is rolled to produce multi-layers.
• Uniformity - To gain physical measures of uniformity of thicknesses of films we propose to image the produced thin films using AFM to build a topographic picture.
• Self-assembling Crystallizing behaviour - our purified proteins are not 100% pure, along with traces of buffers used in the his-tag purification process there are also the tris and triton remnants from vacuum centrifugation. Triton is a detergent and tris is known to crystallize together there is the worry they may be responsible for our observations as opposed to the reflection protein. This worry is strengthened by the purity of this first batch of proteins. It is therefore proposed to carry out further controls with buffers used in the purification process, tris and triton as well as repeating the experiments with a second batch of we believe (higher quality) reflectin proteins.
• Phase-separation - reflectin proteins have been documented in the literature to exhibit phase separation behaviour. Using BMIM as the solvent, reflectin phase separates into diffraction grating with spacings of 8-18μm upon dipping the formed thin-films in water therefore phase separation in HFIP is not unthinkable. It is proposed to investigate further reproduce this self-assembly behaviour in BMIM and investigate the tunability of the grating spacings after formation as well as aiming to reproduce the conditions under which the onset of crystallization was observed in reflectin-HFIP films.

Safety

The new hazards identified with the changes are the liquid CO2 pressure washer and the hot plate. Dr Matthew Hawkeye performed all use with the pressure washer in the fume hood, whilst care was taken with the hot plate, using tweezers and wearing gloves to manipulate the hot substrates and allowing time to cool prior to mounting for microscopy.