"

From 2011.igem.org

Contents 1 August 1 (Mon) 2 August 2 (Tue) 3 August 3 (Wed) 4 August 4 (Thu) 5 August 5 (Fri) 6 August 6 (Sat)

August 1 (Mon)

1. Preparation of LB agar plates (33 Amp, 18 Kan, 17 Cam).

August 2 (Tue)

1. Culture medium preparation
2. Competent cells preparation - Nojima Method
   • SOB medium (MgCl2 not yet added) -> stored at 4˚C
   • Preparation of glucose solution for making SOC medium.
   • Single-colony streaking of E. coli (strain DH5α) on 2 LB agar plates -> 37˚C incubation o/n

Tomorrow we shall prepare the remainder of the reagents and inoculate SOB with o/n-incubated E. coli.

1. Transformation of Registry parts (See Table 1).

Note: 'ID' is an internal identifier used by wet work members to simplify labeling etc. In the case of iGEM distribution parts it usually refers to the plate location.

Table 1

ID	Part Name	Resistance	Description
1-9N	<bbpart>BBa_K118023</bbpart>	A	RecA promoter
1-2M	<bbpart>BBa_K118022</bbpart>	A	RBS
1-14K	<bbpart>BBa_B0034</bbpart>	A	GFP(wild type)
1-12M	<bbpart>BBa_B0010</bbpart>	A	RBS+GFP+double terminator
1-1D	<bbpart>BBa_R0010</bbpart>	A	promoter(lacI regulation)
3-6H	<bbpart>BBa_E1010</bbpart>	A	CrtE I B with RBS
2-18H	<bbpart>BBa_E1010</bbpart>	A	RBS+CrtE
2-16N	<bbpart>BBa_E1010</bbpart>	A	RBS+CrtB
2-18H	<bbpart>BBa_E1010</bbpart>	A	RBS+CrtI
1-17P	<bbpart>BBa_E1010</bbpart>	A	RBS+CrtY
1-1G	<bbpart>BBa_E1010</bbpart>	A	construction plasmid containing mRFP coding device
1-3A	<bbpart>BBa_E1010</bbpart>	C	construction plasmid containing mRFP coding device
1-5A	<bbpart>BBa_E1010</bbpart>	K	construction plasmid containing mRFP coding device

August 3 (Wed)

1. Competent cells preparation (continued)
   • Inoculation of pre-culture SOB from o/n-incubated agar plate colonies.
   • Transfer from pre-culture to growth culture.

August 4 (Thu)

1. OD measurements throughout the day till required OD (0.3~0.7) was obtained.
2. Completion of competent cells according to protocol.

August 5 (Fri)

August 6 (Sat)

1. Transformation of Registry parts (See Table 1).

Note: 'ID' is an internal identifier used by wet work members to simplify labeling etc. In the case of iGEM distribution parts it usually refers to the plate location.

Table 1

ID	Part Name	Resistance	Description
2-20J	<bbpart>BBa_K118023</bbpart>	A	C. fermi endocellulase Cen A coding
2-20H	<bbpart>BBa_K118022</bbpart>	A	C. fermi exocellulase Cex coding
1-2M	<bbpart>BBa_B0034</bbpart>	A	RBS
1-13D	<bbpart>BBa_B0010</bbpart>	A	terminator
1-1D	<bbpart>BBa_R0010</bbpart>	A	promoter
1-18F	<bbpart>BBa_E1010</bbpart>	K	RFP coding

Back to Notebook