Present proteins to the outer membrane

Molecular cloning

We fused GFP to the C-terminal of OmpA and inserted the his-tag in between them. The final plasmid is as follows.

Expression Test

Test for proper inducing conditions

Use 0.5mM IPTG, 18 centigrade, 12 hours induction in later experiments.

Fluorescence microscopy

Green fluorescence is bright.

In order to determine whether GFP is presented outside the membrane, cells were digested with Protease K at 50 centigrade for 30min.

Color Channel	Post-digest	Pre-digest
GFP
DAPI
Merge

The fluorescence disappeared completely after digestion, which seems too good to be true. Hence, we performed Western blotting to be sure of the result.

Western Blotting

The cell components were first fractionated before blotting.

1. Sonicate the bacteria culture.

2. Centrifuge 13000rpm, 30min to separate soluble protein and membrane components from the cell debris and the non-soluble protein.

3. 51000rpm 1h to separate soluble protein from membrane components.

The majority of the OmpA-GFP protein is in the pellet after the first centrifuge, indicating incomplete cell lysis or inefficient protein folding. Nonetheless, from the later result, we can see that it is exclusively in the membrane and not in the soluble proteins.

Expression of Substrate

Molecular cloning

We synthesized the multi-proline sequence and linked it to mCherry.

Test of Expression

After Pro-rich mCherry expression, significant color change can be observed (bacteria cells turned cherry red as a result of mCherry expression)

From left to right, IPTG concentration: 0, 0.1mM, 0.5mM, 1mM

SDS-PAGE

The bacteria culture was sonicated and then centrifuged at 13000rpm for 15min. Both the supernatant and the pellet were loaded onto SDS-PAGE.

Contrary to the sharp change in color, no obvious band can be seen in SDS-PAGE. Hence, further purification of protein is necessary.

Ni-column purification

The cell lysate was then purified by Ni-column. SDS-PAGE indicates that the protein is largely purified.

Western blotting

In order to be sure that the protein we got is multi-proline mCherry, Western blotting was performed.

As is shown, the protein eluted is indeed his-tagged mCherry.

Binding & Release Module

HIV Protease is fused with OmpA to be transported outside the membrane to facilitate substrate release.

SH3 domain is fused with OmpA as the binding module. In order to be readily released, an HIV protease site is settled in the middle.

Bind & Release

E. coli with the plasmid for OmpA-HIV site-SH3 is induced with 0.1mM IPTG at 18 centigrade for 12 hours before harvesting by mild centrifuge.

E. coli expressing OmpA-HIV protease site-SH3 was mixed with mCherry solution at room temperature for 30 minutes.

After washing with distilled water twice, some of the bacteria were fixed on a slip and stained with DAPI.

Color Channel	E. coli with IPTG induction	E. coli without induction
mCherry
DAPI
merge

The remaining were mixed with E. coli expressing OmpA-HIV protease at room temperature for 30 minutes to release the cargo.

After washing with distilled water twice, bacteria were fixed on a slip and stained with DAPI.

Color Channel	+ E. coli expressing protease	+ E. coli without protease
mCherry
DAPI
merge

Chemotaxis

We designed our device for testing chemotaxis. We first build a concentration gradient inside an agar bar as in any other traditional practice. When put in the water, the gradient agar bar will dictate the formation of a concentration gradient in water as solutes inside the agar can diffuse out. We use a dialysis membrane to wrap the bar and some water up, and then stir the water outside the membrane so that excess of solutes can diffuse outside the membrane and maintain the gradient inside the dialysis membrane.

Building agar bar

An agar bar can be built stepwise to generate any gradient we need. We first tried to build an agar bar with a linear gradient of the blue dye.

Test of gradient in water

We tested the formation of gradient in water by color dyes.

This color gradient maintained for over 30min, and is thus suitable for later gradient mediated chemotaxis.

Test of E. coli chemotaxis

All the bacteria used here were washed with distilled water at least twice to remove traces of possible chemoattractant.

We inserted an agar bar into the capsule sealed by dialysis membrane. One end of the agar bar contained a mixture of aspartate, glutamate, serine, threonine, and cystein (10mM each). The bacteria we used was UU1250 E. coli strain (kind gift from Dr. Mark Goulian, U Penn. Δtsr-7028 Δ(tar-tap)5201 Δtrg-100 Δaer-1) harboring plasmid [http://partsregistry.org/Part:BBa_K533009 BBa_K533009], which should has only chemotaxis towards aspartate.

We expected the bacteria to form an obvious concentration difference in the capsule sealed by dialysis membrane, but no obvious difference in the cloudiness was observed in all our experiments. As our modeling put it, in a sealed space like our dialysis capsule, the cells would move towards the destination and turn around randomly, reducing the difference in cell density originally formed by chemotaxis.

Nonetheless, our mathematical model still suggests that certain difference should be present between two ends of the capsule. We took 500ul liquid from either end of the capsule and measured OD600.

As a negative control, we inserted a blank agar bar and took the same measurements.

Statistically we observed a significant difference in cell density between the two ends of the capsule, confirming our hypothesis.

Finally

Thus we built this system with binding, release and transportation abilities to move any protein with multi-proline tag towards the direction dictated by the gradient.