Team:NYMU-Taipei/chassis

From 2011.igem.org

Revision as of 22:19, 5 October 2011 by Sam255676 (Talk | contribs)

Slide Down Box Menu with jQuery and CSS3






Contents

Plasmid Backbones


Promoters


Constitutive


Negatively Regulated


Ribosomal Binding Sites

Cultivation of Magnetospirillum magneticum AMB-1 Actually, it was not difficult...

Like E. coli, AMB-1 also grows in liquid medium, and this medium is called Magnetic Spirillum Growth Medium (MSGM). In the medium, we added nutrient, iron source (supplying AMB-1 in magnetite formation within magnetosomes), vitamin, and mineral solution.


MSGM's ingredients


(In grams per liter)

●Succinic acid             0.74 g
●KH2PO4                    0.68 g
●Sodium nitrate            0.12 g
●Sodium thioglycolate      0.1 g
●*Wolfe's vitamin solution  10 ml(stock)
●*Wolfe’s mineral solution  5  ml(stock)
●Ferric quinate solution   2  ml(0.27 g of FeCl3 and 0.19 g of quinic acid in 100 ml water)
 Adjust pH to 7.0 with NaOH

We also refered to an [http://www.sciencedirect.com/science/article/pii/S014102290100343X original article] published by Chen-Dong Yang, et al., which added Polypeptone , Yeast extract into MSGM and added L-cysteine instead of sodium thioglycolate, which called En-rich MSGM. In <<Effects of growth medium composition, iron sources and atmospheric oxygen concentrations on production of luciferase-bacterial magnetic particle complex by a recombinant Magnetospirillum magneticum AMB-1,2001>> said that MSGM enriched with L-cysteine, yeast extract and polypeptone could enhance BMP (Bacterial Magnetic Particles) productivity. Addition of yeast extract had no effect on BMP (Bacterial Magnetic Particles) production and polypeptone only improved the final cell density and therefore slightly improved BMP (Bacterial Magnetic Particles) production, whereas L-cysteine induced cell growth!


En-rich MSGM's ingredients


(In grams per liter)

●Succinic acid             0.74 g
●KH2PO4                    0.68 g
●Sodium nitrate            0.12 g
*Wolfe's vitamin solution  10 ml(stock)
*Wolfe’s mineral solution  5  ml(stock)

●Ferric quinate solution   2  ml(0.27 g of FeCl3 and 0.19 g of quinic acid in 100 ml water)
L-cysteine                0.005%(Instead of sodium thioglycolate) 
Yeast extract             0.01%
Polypeptone               0.02%
 Adjust pH to 7.0 with NaOH


Strict anaerobic conditions have been thought to facilitate BMP (Bacterial Magnetic Particles) production in AMB-1 cells. To induce AMB-1 forming magnetosome, we have to control low O2 concentration. AMB1.jpg

Electroporation So...how to insert our plasmid into the AMB-1?

After plasmid constructions were done, we need to transform them into AMB-1. Electroporation was performed with a Gene Pulser (Bio-Rad Laboratories, Richmond, Calif.), at a capacitance of 25 micro-F and a resistance of 200Ω, and 0.1-cm cuvettes. Electroporation allows cellular introduction of large highly charged molecules such as DNA which would never passively diffuse across the hydrophobic bilayer core. This phenomenon indicates that the mechanism is the creation of nm-scale water-filled holes in the membrane.


Elem.jpg


Procedure:

● Step1: Harvested and washed AMB-1 with 10 mM TES buffer containing 272 mM sucrose (pH 7.5).
● Step2: Resuspended AMB-1 in the same buffer at 10^9 cells/ml.

● Step3: Transferred to 500 micro-liter of MSGM supplemented with 20 mM Mg2+ and 
incubated at 27°C overnight with shaking at 100 rpm.
● Step4: Diluted in 5 ml of MSGM containing 0.7% agar.

● Step5: Plated on 1% agar in MSGM (supplied with ampicillin at 5 ug/ml or kanamycin at 2.5 ug/ml) 
incubated under anaerobic conditions.