Team:Cambridge/Experiments/Initial Exercise Group Alpha

Fusion of SrfA promoter with GFP

Aim

Our week 1 experimental challenge was to generate a temporal and or spatial pattern of GFP expression in Bacillus subtilis, using Gibson Assembly to join a sequence of interest to a GFP coding plasmid. We chose to visualise sporulation via a fusion of SrfA promoter with GFP.

Role of SrfA

• SrfA codes for surfactin production, a protein that is produced by B. subtilis prior to sporulation.
• SrfA is regulated by ComA, a protein which itself responds to an intercellular population-density-signalling molecule, CSF, in a concentration dependent manner.
• ComA has low activity at low CSF concentration(low population density), highly active as CSF levels increase, and less active at high CSF concentrations.

Construct Design

We wish to:

• keep the original promotor for SrfA and comA boxes
• remove GFP promotor sequence
• maintain ComGA stabiliser sequence
• do not include restriction sites

Predicted results

• Bacillus colonies exhibit a range of colony patterns and superimposed on the colony shape we expect a temporal pattern of green fluorescence marking sporulation activity.
• intially zero or low GFP detection, higher GFP activity on activation of SrfA prior to sporulation.
• Flourescence will mark spatially sporulation sites.

Method

fig 1. Primer datasheet

• 20bp primers with 20bp tails were designed to perform Gibson assembly to fuse the SrfA promoter with a plasmid containing GFP.
• 100 μM stock solutions of the primers were made and subsequently diluted four-fold to make 25μM 'working solutions'
• Particular care was taken in preparing the inital stock as these affect all future dilutions and were 'contingency' solutions in case of mistake.
• Genomic DNA of B. subtilis were provided and the vector plasmid containing GFP in two fragments
• The two primers to combine the two fragments of the plasmid were provided.

Our three PCR reactions consisted of:

1.

1μl primer JMF2

1μl primer JMF3

1μl B. subtilis genomic DNA

2.

1μl primer JMF1

1μl primer A Forward (provided)

1μl vector DNA

3

1μl primer JMF4

1μl primer B reverse (provided)

1μl vector DNA

to each tube we also added:

9.5μl of water

12.5μl Master mix (SyBR Green and Rox, Hotstart Taq polymerase, dNTPs and dyes)

for a total volume 25μl

The complete tubes were run in a real-time PCR machine for 30 cycles with a 2 minute extension time and a primer annealing temperature of 50ºc.

Technical Data

We used Finnzymes melting temperature calculator to work out the melting temperature of the primer part (not the tail) of our Gibson Assembly oligos (this was the 3' 20bp of each oligo) these values in ºC are shown below

JMF1 - 56.91 JMF2 - 68.8 JMF3 - 50.48 JMF4 - 53.09

Results

fig 2. Results from PCR reaction

• reaction 1 and 3 were amplified in the PCR however reaction 2 was not
• It is suspected this was a result of a compromise run of the PCR where:
  • annealing temperature set at an arbitrary 50ºc to produce annealling for every group
  • primer extension time was arbitrarily set at 3 mins
• Results from all groups indicated the PCR failed for the longest fwdA fragment which we ascribe to the use of the Taq and not phusion polymerase
• It is intended to carry out the PCR again using Phusion polymerase.

References

Sporulation occurs late in the life cycle of B. subtilis when the colony reaches a high population density and we hope that GFP could be visualised following overnight growth. This paper[http://www.ncbi.nlm.nih.gov/pmc/articles/PMC1178101/?page=2] details some sporulation inducing culture conditions.