Team:Calgary/Notebook/Protocols/Process5
From 2011.igem.org
Revision as of 01:12, 27 September 2011 by Emily Hicks (Talk | contribs)
![](https://static.igem.org/mediawiki/2011/c/c1/UCalgary_CircleHome.png)
![](https://static.igem.org/mediawiki/2011/d/d4/UCalgary_CircleTeam.png)
![](https://static.igem.org/mediawiki/2011/7/7d/UCalgary_CircleProject.png)
![](https://static.igem.org/mediawiki/2011/8/8d/UCalgary_CircleParts.png)
![](https://static.igem.org/mediawiki/2011/0/03/UCalgary_CircleNotebook.png)
![](https://static.igem.org/mediawiki/2011/8/84/UCalgary_CircleOutreach.png)
![](https://static.igem.org/mediawiki/2011/3/3c/UCalgary_CircleSponsors.png)
![](https://static.igem.org/mediawiki/2011/8/85/UCalgary_CircleiGEM.png)
![](https://static.igem.org/mediawiki/2011/4/42/UCalgary_TitleBar.png)
Preparation of f2 media for algae
![](https://static.igem.org/mediawiki/2011/e/ed/UCalgary_BodyBoxTop.png)
This protocol is used to prepare f2media for algae growth
Procedure
- Add 0.5 mL of each of stock solutions 1-5 (listed below) to 1 L of seawater
- Split into flasks and autoclave at 121 °C (15 PSI) for 15 minutes
- Prepare phosphate solution (see below) and autoclave dilute phosphate stock at 121°C (15PSI, 15 mins). After cooling, dispense aseptically with sterilised automatic dispenser. This component is autoclaved separately in order to prevent precipitation
Stock solutions
- NaNO3 (150.0 g/L)
- Trace metals (mixed to 750 mL to dissolve, and then brought up to 1 L): CuSO4.5H2O (19.6 mg/L), ZnSO4.7H2O (44.0 mg/L), CoCl2.6H2O (22.0 mg/L), MnCl2.4H2O (360.0 mg/L), Na2MoO4.2H2O (12.6 mg/L)
- Na2SiO3.5H2O (22.7 g/L)
- Fe citrate (both constituents added to the same 1 L: ferric citrate (9.0g/L), Citric acid (9.0g/L)
- Vitamins: create primary stocks of Biotin (10.0 mg/100 mL) and vitamin B12 (10.0 mg/100 mL).
- Create a working solution of 100 mL, fresh every three months, containing: 1.0mL primary stock Biotin, 1.0 mL Vitamin B12, 20.0 mg Thiamine HCL).
- NaH2PO4.2H2O (11.3 g/L)
Further purification (Plasmid from putida)
- Layer the resuspended DNA on a 2.5mL bed of saturated CsCl in a polymer tube. Centrifuge for 14hr at 14 000 rpm in a fixed-angle 30 rotor at 2°C. After the run, ~25mL of liquid can be discarded from the top without disturbing the remainder. Mix the lower part to form the concentrated lysate.
- Slowly dissolve ~5.7g CsCl to the concentrated lysate, until the refractive index is 1.399. Mix solution with Syber-safe or gel-red. Centrifuge for 40hr in a Spinco fixed-angle rotor 50 at 105 000 x g at 12°C. After this run, 2 well-separated bands should be able to be seen. Alternatively, do only this spin where DNA mixed with CsCl is concentrated to a refractive index of 1.399 with the fluorescent DNA stain.
- Because the DNA was infused with dye, 2 well-separated bands will appear. The upper band is linear and non-circular DNA (junk). The lower band is the plasmid of interest. Remove the upper layer with a micropipette. After it is removed, pool bands from several tubes centrifuge again SW50.1 rotor for 20h at 40 000rpm. Again there will be 2 bands and the lower band is the desired intact plasmid.
![](https://static.igem.org/mediawiki/2011/c/cb/UCalgary_BodyBoxBottom.png)