Reporter: Week 8 July 3-July 9

From 2011.igem.org

Revision as of 22:31, 30 July 2011 by Ajb5663 (Talk | contribs)

Contents

Sunday, July 3

Assembly of Fusion Parts, Day 5

     All of the assemblies from 7/2 and the promoter+RBS assembly (J23100+B0034) were verified using agarose gel electrophoresis. Since the ladder was contaminated, the relative sizes of the assemblies were analyzed. This analysis showed that the J23100+B0034 was much smaller than the other assemblies, the XylE+both linkers were just under 1000 base pairs, and the GFP+cleavage sites were a little smaller than the XylE+linker parts. Thus, each construct was grown in culture overnight in order to extract plasmids for sequencing.

     Plasmids from the four cultures made on 7/1 were extracted using the Omega Bio-Tek miniprep protocol. These plasmids were stored in the 4°C fridge until they could be sent to sequencing on 7/5.

Monday, July 4

Assembly of Fusion Parts, Day 6

     Plasmids were extracted from the eight cultures made on 7/3 using the Omega Bio-Tek miniprep protocol. Since the sequencing center is closed for the holiday, these plasmids will be sent to sequencing tomorrow, along with the plasmids extracted on 7/2.

Tuesday, July 5

The following plasmids were sent to sequencing:

J23100+B0034 (A and B)

LacZ+Imp linker

LacZ+Small linker

LacZ+10 AA linker

XylE+Imp linker

XylE+Small linker

XylE+10AA linker

GFP+cI cleavage site (A and B)

GFP+tev cleavage site (A and B)

Results: The J23100+B0034 (colony A) sequence results showed that the assembly worked, so now we have a promoter in front of a ribosome binding site. The cells from this colony were used for freezer stock. The rest of the plasmids were vector background and were discarded.

The linkers were inserted behind XylE and the cleavage sites were inserted behind GFP.

Protocol Part Involved with Protocol
Restriction Digest Inserts using PstI and NgoMIV: small linker
Imp linker
10AA linker
cI cleavage site
tev cleavage site
Vectors using PstI and AgeI: GFP
XylE
Ligation XylE+small linker
XylE+Imp linker
XylE+10AA linker
GFP+cI cleavage site
XylE+tev cleavage site
Transformation/Plating The above ligations were transformed into
Escherichia coli cells and plated on kanamycin
resistant plates.

Wednesday, July 6

Prepared M9 media following this protocol.

The assemblies from Tuesday, July 5 were verified through gel electrophoresis. The gel showed bands all slightly above 1 kbp, so two colonies of each of the constructs were grown in culture overnight.

Thursday, July 7

The following plasmids were extracted for sequencing:

GFP+tev cleavage site (A and B)
GFP+cI cleavage site (A and B)
XylE+small linker(A and B)
XylE+Imp linker (A and B)
XylE+10AA linker (A and B)

Results: The GFP+tev cleavage site, GFP+cI cleavage site, XylE+small linker, XylE_Imp linker and XylE+10AA linker all looked good, so the cells containing these plasmids were used for freezer stock.

The promoter+RBS (J23100+B0034) construct placed in front of GFP+cleavage sites and XylE+linkers.

Protocol Part Involved with Protocol
Insert PCR J23100+B0034
Restriction Digest Insert using EcoRI and SpeI: J23100+B0034
Vectors using EcoRI and XbaI: GFP+tev cleavage site
GFP+cI cleavage site
XylE+small linker
XylE+Imp linker
XylE+10AA linker
Ligation J23100+B0034+GFP+tev cleavage site
J23100+B0034+GFP+cI cleavage site
J23100+B0034+XylE+small linker
J23100+B0034+XylE+Imp linker
J23100+B0034+XylE+10AA linker
Transformation/Plating The above ligations were transformed into
Escherichia coli cells and plated onto kanamycin
resistant plates.


Back to Notebook