Plug 'n' Play with DNA assembly standard
|
Making molecular biology easier
We imagine that iGEM should be about assembling BioBricks fast, leaving more time for the actual project. It should be easy to combine any thinkable part, device or existing BioBrick. Unfortunately, classical cloning techniques can cause problems and even PCR can be cumbersome, if you have little or no laboratory experience.
Successful assembly of six biological parts in one reaction is possible, reducing the plasmid construction time significantly. The upper limit of fragments that efficiently can be assembled has not been delineated yet (1). Owing the 8-9 nucleotide overhangs flanking the parts, they can hybridize to complementary overhangs without the use of DNA-ligases. How it worksWe have demonstrated that successful assembly of up to six biological parts in one reaction is possible e.g. (BBa_K678068). The entire process of combining six BioBricks is illustrated in the figure below. The number of BioBricks can be adjusted as preferred and for instance mutations can easily be introduced by customizing the standard.
The Procedure of assemblyPlease refer to our Biobrick Assembly Standard BBF RFC 80 for a detailed protocol.1. Pre-produced PCR products are picked from the Plug `n´ Play kit. 2. USER enzyme mix and buffer is added. This will remove the uracil, making sticky end overhangs on all BioBricks. All BioBricks and backbone plasmid have matching sticky ends, and the BioBricks will self-assemble in the plasmid. 3. Transformation in E. coli. Reduced incubation of the transformation mix is obtained when using ampicillin as antibiotic resistance marker. If a part is not incluede in the Plug `n´ Play kit a simple PCR amplification can performed on the part or BioBricks intended for the assembly. The PCR product should subsequently be gel band purified. Plug 'n' Play benefitsImprovements of BBF RFC 39• No need to use a USER cassette, thereby completely avoiding the use of restriction enzymes.• Standardized linkers What you get• Rapid assembly of biological parts• A well documented system • Assembly of multiple biobricks in one step • No illegal restrictionsites • 100% restriction enzyme free • 100% DNA ligase free • High fidelity ensured by PfuTurbo® 7x Hotstart DNA polymerase • Directionality of inserts are supported • Any vector can be made Plug’n’Play compatible • Suitable for large scale high throughput projects
Vectors for Plug `n´ Play have been prepared by PCR ensuring 100% linear fragments. This means that the occurrences of false positives due to the presence uncut vector can be completely avoided (2).
Drawbacks of the USER cassette (2): The USER compatible backbone vectors were made by PCR amplification with primers containing the standardized linkers 6 and 1. For all the PCR reactions it is important to remove the template vector, to ensure assembly in USER reaction and avoid inauspicious transformation and false positive. The template can simply be removed by DpnI treatment (2). However, a gel band purification was instead performed, when preparing the vector to further ensure a high degree a purification of our BioBricks. Previous studies have demonstrated a high level of correct assembly and directionality of fragments (2,3) and although we did not make such analysis ourselves it was in general our perception that this was the case, of the more than 25 different Plug `n´ Play assemblies we performed we encountered no more than 2 false-positives. It is well known that mutations can be introduced during PCR. To minimize mutations the X7 proof-reading polymerases (4) are used which are fully compatible with the Plug `n´ Play standard. The x7 proof-reading polymerase helps lowering the risk of introducing mutations. The concern for introduction mutations is specially regarding the gene of interest (GOI), because mutations occurring in the vector backbone or resistance cassette would in worst case scenario mean the vector might not be able to propagate. The Design of The SystemThe system is designed in order to assemble BioBricks from the categories promotor, a gene of interest (GOI), a targeting signal (TS), a terminator, a marker cassette and a vector backbone. The marker cassette consist of a promoter, a resistance gene, and a terminator. Ribosome binding site (RBS) is integrated in the promoter. However, a RBS can if needed be integrated in the reverse primer of the promoter when amplifying by PCR. This was the case when constructing the BioBricks and devices for the iGEM team Copenhagen.
The system is depending on custom-made overhangs on each part to be assembled. The parts with overhangs is formed by PCR amplifying the target DNA using primers designed with an upstream extension of 8-9 additional nucleotides that ends in a single deoxyuridine residue. In order to assembled multiple parts and having a flexible system the final DNA extension is preferred to consist of a adenine in the 5' end and a thymine in the 3' end.
Furthermore, the it is important that the overhangs (tails) of the different parts are not identical to ensure directionality and correct order of the biobricks. ![]() ![]() The linkers are making the whole system flexible in that it is possible use any promoter, since it will all ways end up have the same overhang generated in the PCR reaction. In the Plug `n´ Play system we are distinguishing between having a gene of interest where a targeting signal or reporter is wanted or not. Therefore, a GOI is a a gene of interest without any reporter or targeting signal, which can be assembled with a TS targeting signal or reporter. However, if the gene of interest is wanted without any reporter or targeting signal, we call it a module. A module can also include a gene of interest where the a targeting signal is included already or if it is a reporter by itself. References(1) Hansen, B.G.; Salomonsen, B.; Nielsen, M. T.; Nielsen, J. B.; Hansen, N. B.; Nielsen, K. F.; Regueira, T. B.; Nielsen, J.; Patil, K. R.; Mortensen, U. F.; “Versatile enzyme expression and Characterization system for Aspergillus, with the Penicillium brevicompactum Polyketide Synthase Gene from the Mycophenolic Acid Gene Cluster as a Test Case.” American Society for Microbiology, 2011, 3044-3051. (2) Hansen, B. G.; Holm, D. K.; Nielsen M.T.; Mortensen, U.H. PCR based USER cloning for restriction enzyme and ligase-independent vector construction. Manuscript. (3) Frandsen, R. J. N.; Andersson, J.A.; Kristensen, M. B.; Giese, H. Efficient four fragment cloning for the construction of vectors for targeted gene replacement in filamentous fungi. BMC Molecular Biology 2008, 9:70. (4) Nørholm, M. H. H. A mutant Pfu DNA polymerase designed for advanced uracil-excision DNA engineering. BMC Biotechnol. 10, 21 (2010). |