"
Team:Paris Bettencourt/T7 diffusion
From 2011.igem.org
| Line 53: | Line 53: | ||
<p>To know more about what we have done with this system, we invite you to visit the corresponding <em>modeling</em> and <em>experiment</em> pages:</p> | <p>To know more about what we have done with this system, we invite you to visit the corresponding <em>modeling</em> and <em>experiment</em> pages:</p> | ||
<ul> | <ul> | ||
| - | <li><a href="https://2011.igem.org/Team:Paris_Bettencourt/Modeling/T7_diffusion">Modeling</a></li> | + | <li><em><a href="https://2011.igem.org/Team:Paris_Bettencourt/Modeling/T7_diffusion">Modeling</a></em></li> |
| - | <li><a href="https://2011.igem.org/Team:Paris_Bettencourt/Experiments/T7_diffusion">Experiments</a></li> | + | <li><em><a href="https://2011.igem.org/Team:Paris_Bettencourt/Experiments/T7_diffusion">Experiments</a></em></li> |
</ul> | </ul> | ||
<br/> | <br/> | ||
Revision as of 19:58, 20 September 2011
The T7 RNA polymerase design
|
Bacteriophage T7 RNA polymerase is a DNA-dependant RNA polymerase from the T7 bacteriophage genome. The enzyme is composed of a single polypeptide chain of 880 amino acids. It catalyzes the processive polymerization of messenger RNA from nucleoside triphosphate precursors by using one strand of DNA as a template . This enzyme is known to have a stringent specificity for its promoter, that is orthogonal to the other promoter of the cell. In our designs, we wanted a protein to pass molecules through the tubes and trigger a signal in the receiver cell. T7 RNA polymerase is seen a very good candidate for such systems. This explains why it is used as the biggest of our proof of principle molecules. |
 Fig1: Cristallographic structure of RNA polymerase. (source) |
Making the T7 RNA polymerase diffuse through the tubes
When we calculated the radius of the T7 RNA polymerase we noticed that it is smaller than the average size of the nanotubes we can measure from the Ben-Yehuda paper. We made the hypothesis that such a big molecule have the chance to pass through the tubes and we started building the design to test it.
- In the emitter cell, we have to over express the T7 polymerase. As we said in the general overview the production of T7 polymerase is under the control of an IPTG inducible promoter design. The RFP, placed on the same mRNA is a reporter of the quantity of the produced T7 polymerase.
- In the receiver cell, a system sensitive to the T7 polymerase will be activated if a T7 polymerase reaches its promoter, present in a few plasmids of the receiver cell (low copy plasmids). The system is self-amplifying and the GFP is produced as a monitor of the signal.
The principles of the design are summed up in the image below:
Fig2: Schematic summary of the T7 diffusion device
T7 polymerase as an auto-amplifier
One of our first concern was the potential leaking from the auto amplifier. Biological systems tend to be noisy. The promoter is known to be very orthogonal to the metabolism of the host. However, we had to deal with several problems. We invite you to see the experiments page for data about this.
We could not work in a synthetic biology plasmid since it does not exist for B.subtilis. We had to create and use a home made, non biobricked multihost plasmid, not designed to be silent. We hade to add several stops before the pT7 promoters in order to prevent the leakage.
As an alternative solution, we also constructed a GFP with a T7 promoter. This system is supposed to have a lower response, but without auto-amplification leaking should be reduced to a minimum.
Model and experiments
To know more about what we have done with this system, we invite you to visit the corresponding modeling and experiment pages:
