Team:Cambridge/Experiments/Initial Exercise Group Alpha

Fusion of SrfA promoter with GFP

Aim

Our week 1 experimental challenge was to generate a temporal and or spatial pattern of GFP expression in Bacillus subtilis, using Gibson Assembly to join a sequence of interest to a GFP coding plasmid which we will amplify in E. coli. We chose to visualise sporulation via a fusion of SrfA promoter with GFP.

Role of SrfA

• SrfA codes for surfactin production, a protein that is produced by B. subtilis prior to sporulation.
• SrfA is regulated by ComA, a protein which itself responds to an intercellular population-density-signalling molecule, CSF, in a concentration dependent manner.
• ComA has low activity at low CSF concentration(low population density), highly active as CSF levels increase, and less active at high CSF concentrations.

Construct Design

We wish to:

• keep the original promotor for SrfA and comA boxes
• remove GFP promotor sequence
• maintain ComGA stabiliser sequence
• do not include restriction sites

Predicted results

• In E. coli we do not expect to see any fluorescence.
• Bacillus colonies exhibit a range of colony patterns and superimposed on the colony shape we expect a temporal pattern of green fluorescence marking sporulation activity.
• intially zero or low GFP detection, higher GFP activity on activation of SrfA prior to sporulation.
• Flourescence will mark spatially sporulation sites.

Materials

fig 1. Primer datasheet

• 20bp primers with 20bp tails were designed to perform PCR to amplify our chosen DNA sequences and Gibson Assembly to fuse the SrfA promoter with a plasmid containing GFP.

We used the Finnzymes melting temperature calculator to work out the melting temperature of the primer part (not the tail) of our Gibson Assembly oligos (this was the 3' 20bp of each oligo) these values in ºC are shown below

JMF1 - 56.91 JMF2 - 68.8 JMF3 - 50.48 JMF4 - 53.09

• 100 μM stock solutions of the primers were made and subsequently diluted four-fold to make 25μM 'working solutions'
• Particular care was taken in preparing the initial stock as these affect all future dilutions and were 'contingency' solutions in case of mistake.
• Genomic DNA of B. subtilis were provided and the vector plasmid pJS104-sfGFP containing the superfolded GFP gene.
• The two primers for two fragments of the plasmid were provided.

PCR -- taq

Our three PCR reactions consisted of:

1.

1μl primer JMF2

1μl primer JMF3

1μl B. subtilis genomic DNA

2.

1μl primer JMF1

1μl primer A Forward (provided)

1μl vector DNA

3

1μl primer JMF4

1μl primer B reverse (provided)

1μl vector DNA

to each tube we also added:

9.5μl of water

12.5μl Master mix (SyBR Green and Rox, Hotstart Taq polymerase, dNTPs and dyes)

for a total volume 25μl

fig 2. Results from PCR reaction using taq

The complete tubes were run in a real-time PCR machine for 30 cycles with a 2 minute extension time and a primer annealing temperature of 50ºc. Two of these were successfully copied but one of the plasmid fragments failed.

PCR -- Phusion(TM)

We used the same primers and templates as above, but we made a new master mix including phusion, a more processive and higher fidelity polymerase. Each PCR tube contained a total volume 25μl, which was comprised of:

5ul buffer 0.5ul dNTP 0.25ul phusion polymerase 16.25ul H2O 1μl of each primer 1μl of template DNA

We used gel electrophoresis to check the results and isolate our fragments.

Gibson Assembly

In order to combine the fragments of the GFP containing fragment and our chosen sequence of interest (SrfA promoter) we performed Gibson Assembly.

The amplified fragments from the PCR reaction above were added into a PCR tube with a Gibson assembly master mix

The thermocycler was set at 50 degrees C for 1 hour.

Transformation of E. coli and amplification

Following Gibson Assembly we transformed E.coli with the DNA we had combined. See the protocols page for how to do Transformation of E.coli. We transformed and plated our E. coli on a medium containing ampicillin and left them to incubate overnight. In the morning we observed 5 colonies on our plate.

To our surprise, the E. coli colonies did exhibit fluorescence when viewed under a light microscope.

References

Sporulation occurs late in the life cycle of B. subtilis when the colony reaches a high population density and we hope that GFP could be visualised following overnight growth. This paper[http://www.ncbi.nlm.nih.gov/pmc/articles/PMC1178101/?page=2] details some sporulation inducing culture conditions.