Team:HKUST-Hong Kong/characterization.html

BioBricks Master List

&

Characterization Data

1. BBa_K524000 –oriR101 & repA101-ts: This heat sensitive origin of replication origin has been shown to be function at 30°C Partial loss of plasmid happens at 33°C, and complete loss of plasmid is observed at 37°C.


2. BBa_K524001 –pLac + RBS + sfGFP1-10: This contains coding DNA sequences for superfolder GFP amino residues 1-214 driven by RBS BBa_B0034 and pLac BBa_R0010.


3. BBa_K524002 –pLac + RBS + sfGFP11 + double terminator: This contains coding DNA sequences for superfolder GFP amino residues 215-238 driven by RBS BBa_B0034 and pLac BBa_R0010, with double terminator B0015 at the end.


4. BBa_K524003 – nadE gene + double terminator: an essential gene that encodes constitutive expressed NAD+ synthatase.


5. BBa_K524004 –pir gene: the pir gene encodes the autogenously regulated pi protein.


6. BBa_K524005 – pToolkit: A plasmid that is only maintained in strains with genotype pir+. The plasmid was modified from another plasmid pKD46, which has been shown to trigger DNA recombination and subsequent gene knockout under induction of arabinose.


7. BBa_K524006 –RBS + sfGFP1-10: This contains coding DNA sequences for superfolder GFP amino residues 1-214 driven by RBS BBa_B0034.


8. BBa_K524007 –RBS + sfGFP11 + double terminator: This contains coding DNA sequences for superfolder GFP amino residues 215-238 driven by RBS BBa_B0034, with double terminator B0015 at the end.


9. BBa_K524100 – bcr CDS + double terminator B0015: The gene product is responsible for multidrug efflux system that pumps out antibiotics. Effect of pump was documented by other researchers: it confers varying degrees of resistance to 5 antibiotics.

Characterization Data for BBa_K524000

Heat Sensitive Origin of Replication (oriR101 & repA101-ts)

Abstract

oriR101 & repA101-ts constitute a low copy origin of replication derived from the pSC101 replication origin. Initiation of replication at oriR101 is regulated in trans by the heat-labile protein product of repA101-ts, which loses activity significantly at 37°C. Hence when bacteria harboring plasmids with this origin are incubated at 37°C, the activity of this origin would decrease, while temperatures higher than 42°C would cause the construct to cease its functions completely. (Datsenko, K.A. and Wanner, B.L. 2000).

In the process of its fabrication, a point mutation was introduced (base substitute of C to G at nucleotide residue 1391) so as to make the construct compatible with Biobrick standard assembly requirements. Nevertheless, our characterization results do not seem to suggest great impacts to the construct's functions, causing only a slight increase in its thermosensitivity.

Construction of This Part

This construct was cloned out from the pKD46 plasmid harboured in the E. coli strain BW25113 (courtesy of The Coli Genetic Stock Center). A single nucleotide mutation, performed through overlapping PCR, was introduced to eliminate a SpeI cut site originally present inside the construct between the promoter and CDS of the ori101R & repA101-ts. The mutation has been successfully confirmed by restriction digestion (Figure 1) and nucleotide sequencing.

#Figure 1: Digestion with SpeI for Confirmation of Successful Mutation

Characterization

• Construct Preparation for Heat Sensitivity Test

Characterization of the oriR101 & repA101-ts was done with the insert ligated to RFP reporter and harbored in partregistry.org's standard assembly pSB1AK3 plasmid. The enzymes PstI and SmaI were then used to cut out the normal replication origin (pMB1) of pSB1AK3 and part of its KanR gene. After the blunt end treatment, the linearized plasmid was self-ligated and transformed into E. coli DH10b. Restriction digestion test, along with the presence of red fluorescence and absence of Kanamycin resistance, is used for plasmid verification. The final construct used for thermosensitivity test is referred to as “ori-ts” for convenience.

• Characterization Methods

• Qualitative Test

• Quantitative Test

• Characterization Results

• Qualitative Test

Several sets of serial dilution tests were done at 30°C, 33°C, 37°C and 42°C. The evidence and results are shown below.

#Figure 2: Qualitative Description of the Temperature Sensitivity Test data.

For each temperature point in the gradient, the most concentrated O/N culture was applied on the leftmost-side, and serially diluted by 10-fold towards the rightward direction.

A robust growth of ori-ts(+) cells was observed when the cells were incubated at 30°C. This robustness (indicated by the density of bacterial colonies in each droplet, and associated with the proper functioning of the plasmid's heat sensitive origin) steadily declined as the incubation temperature was increased. Partial replication origin dysfunction was observed after 33°C incubation, and near-complete loss of function was observed at 37°C. Comparing this trend with the tested result of the original oriR101 & repA101-ts in pKD46 (partial loss of function observed at 37°C, and near-complete loss of function at 42°C), the mutated one shows higher thermosensitivity.

• Quantitative test

The result of the quantitative thermosensitive test and trend of the % elimination of ori-ts is shown by the following graph:

#Figure 3: Quantitative Analysis of the temperature sensitivity origin.

Conclusion

This pKD46-derived oriR101 & repA101-ts displays thermosensitive properties, which have seems to be intensified. This might be due to the point mutation introduced during the fabrication of the construct. The optimal incubation temperature for plasmid maintenance purposes is 30°C, whereas our recommended temperature for plasmid loss induction is 37°C or above.

Home

Our Project

Overview | Data Page
Experiments and Results
Strain Construction | Culture Tests | Modeling
Miscellaneous
Notebook

iGEM Resources

Acknowledgements
The Team
iGEM Member List | Contributions
Achievements
Medal Requirements | BioSafety
BioBricks
Master List & Characterization Data

Human Practice

Workshop | Survey