Team:ETH Zurich/Biology/MolecularMechanism

Plasmid design

Table 1: Plasmid design for the AlcR system Transcriptional terminators included for each gene. Plasmid copy numbers adapted from [4].

Table 2: Plasmid design for the XylR system Transcriptional terminators included for each gene. Plasmid copy numbers adapted from [4]. For a detailed description of the pCK04AxylR plasmid see [1].

For the biological implementation of the SmoColi system, we constructed a three-plasmid system with different antibiotic resistances. This setup was chosen in order to clone the whole SmoColi system into the same bacterial cells.

The vectors used in our setup are the parts pSB6A5, pSB3C5, pSB3K3 and pSB4K5. These plasmids contain different origins of replication, thus resulting in different copy numbers of the correlating plasmid in E.coli. pBR322, p15A and pSC101 origins are used as a stable three-plasmid system [3]. The copy number influences the amount of protein produced by the cell and plays a crucial role in our design, especially for the bandpass filter. Depending on the function of a particular protein in our system we had to evaluate on which plasmid the corresponding gene should be cloned.

In the xylene-responsive system we included an artificial degradation pathway (xylWCMABN) so that we could establish a xylene gradient. For this purpose the plasmid pCK04AxylR was added [1]. To avoid incompatibilities of plasmids we adapted the rest of our system and changed the composition of the genes on each vector compared to the AlcR system.

Cloning strategy

General procedure

By cloning our parts we tried to follow as much as possible to the strategies proposed in the registry of standard biological parts [5]. The general cloning scheme was performed as follows:

• If available, genes and promoters in SmoColi were obtained from the iGEM spring 2011 distribution kit. A codon-optimized version of alcR and P_tet-lacI_M1 were synthesized. P_alc- and P_U-promoters were obtained by PCR.

• After isolation of the DNA, ribosome binding sites and prefix (5' gaattcgcggccgcttctagag 3') respectively suffix (5' tactagtagcggccgctgcag 3') were added to the gene by polymerase chain reaction. The PCR products were purified and afterwards digested with XbaI-PstI.

• Plasmid vectors containing the corresponding promoter were linearized by SpeI-PstI and the XbaI-PstI fragment containing the gene of interest was ligated into the backbone.

• In a next step we isolated a EcoRI-SpeI fragment with promoter, ribosome binding site and gene and inserted it into a EcoRI-XbaI cut vector containing a transcriptional terminator.

• In the end all the constructed parts were assembled on the corresponding vectors for the final SmoColi system. Some parts (especially lacI in an actively expressed form) appeared to be negatively selected by E.coli. So we had to assemble the parts in a way that lacI was always repressed.

Sources of genes and promoters

Table 4: Promoters of SmoColi: source and final constructs of the different used promoters

Table 3: Genes of SmoColi: source and final constructs of the different used genes

Problems

• For cloning lacI and cI behind the P_tet we obtained mutations in the lacI and cI genes, respectively. We tried to perform whole plasmid PCRs to get rid of these mutations without any success. This is due to the fact that high LacI or CI expression is lethal to the cells, leading to a selection for clones mutated in a way that lacI or cI is not expressed, for example by deletion of the RBS. For cloning lacI or cI behind P_tet you have to make sure that the genes are not expressed in a non induced state.

Definition of ribosome binding sites

Table 5: Different ribosome binding sites and their estimated strengths which are included in our design. The strengths of the sequences were estimated with a RBS strength calculator [7]. In the last column it is listed in front of which genes a particular RBS was added.

Another important role in the synthesis of proteins plays the ribosome binding site (RBS), where the ribosomes are bound to the mRNA at the initiation of the translation process. The ribosome binding sites which we included in our system were designed in several different ways:

• For the bandpass filter we implemented the ones which are also used for the plasmids in [2].

• For the other parts we either tried to use naturally ocurring ribosome binding sites or took specific ones from the Anderson library of ribosome binding sites [6].

The strength of all the ribosome binding sites used was estimated with a RBS calculator [7]. Although the efficiency of protein synthesis is not directly proportional to the estimated values, they can still indicate whether a certain RBS is more or less strong. Below you can find a list of the different ribosome binding sites used, their estimated binding strength and in front of which genes they were put.

References

[1] [http://aem.asm.org/cgi/content/abstract/64/2/748 Sven Panke, Juan M. Sánchez-Romero, and Víctor de Lorenzo: Engineering of Quasi-Natural Pseudomonas putida Strains for Toluene Metabolism through an ortho-Cleavage Degradation Pathway, Appl Environ Microbiol, February 1998, 64: 748-751]

[2] [http://www.nature.com/nature/journal/v434/n7037/full/nature03461.html Subhayu Basu, Yoram Gerchman1, Cynthia H. Collins, Frances H. Arnold & Ron Weiss: A synthetic multicellular system for programmed pattern formation, Nature, 2005, 434: 1130-11342]

[3] [http://www.springerlink.com/content/3fj1xxl9p42kx8l5/ Karl Friehs: Plasmid Copy Number and Plasmid Stability, Advances in Biochemical Engineering/Biotechnology, 2004, 86: 22-192]

[4] [http://openwetware.org/wiki/Arking:JCAOligoTutorial8 OpenWetWare Arking: JCAOligoTutorial8, 0 Jul 2008, 04:32 UTC. 21 Sep 2011, 01:32]

[5] [http://partsregistry.org/Help:Contents Registry of Standard Biological Parts Help:contents 21 Sep 2011, 02:59]

[6] [http://partsregistry.org/Ribosome_Binding_Sites/Prokaryotic/Constitutive/Anderson J. Christopher Anderson Ribosome Binding Sites/Prokaryotic/Constitutive/Community Collection Registry of Standard Biological Parts, 21 Sep 2011, 08:49]

[7] []