|
|
| (143 intermediate revisions not shown) |
| Line 1: |
Line 1: |
| - | {{Template:Team:Cambridge/CAM_2011_TEMPLATE_HEAD}}
| |
| | | | |
| - | This is a placeholder. We should fill it in.
| |
| - |
| |
| - | ==Construct Design==
| |
| - | ==Primer Design==
| |
| - | We should mention expected lengths of products here.
| |
| - |
| |
| - | ==Assembly: first attempt==
| |
| - | ===PCR===
| |
| - | In the first round of PCR, we amplified fragments required for the assembly of GA1, GA2, GA3 and GA4 constructs.
| |
| - | *We performed PCR using [[Team:Cambridge/Protocols/PCR#Reagents_used_in_PCR_reaction | Phusion Hot Start DNA Polymerase]] in 20 μl reaction volume.
| |
| - | *The time profile used in the PCR machine was the following:
| |
| - | {| border="1" align="center" style="text-align:center;"
| |
| - | |scope="col" width="50" | '''Hold'''
| |
| - | |
| |
| - | |95°C
| |
| - | |2 min
| |
| - | |-
| |
| - | |scope="col" width="50" rowspan="3" | '''Cycling'''
| |
| - | |scope="col" width="80" | ''Denaturing''
| |
| - | |scope="col" width="50" | 95°C
| |
| - | |scope="col" width="50" | 10 s
| |
| - | |-
| |
| - | |scope="col" width="80" | ''Annealing''
| |
| - | |scope="col" width="50" | 55°C
| |
| - | |scope="col" width="50" | 20 s
| |
| - | |-
| |
| - | |scope="col" width="80" | ''Elongation''
| |
| - | |scope="col" width="50" | 72°C
| |
| - | |scope="col" width="50" | 150 s
| |
| - | |}
| |
| - |
| |
| - | We decided to use the 55°C annealing temperaure, although the predicted temperature for most primers is 5-10°C higher, because of a low annealing temperature of the VF2 primer.
| |
| - | *Primers and template DNA provided by our supervisor Paul served as a positive control, but eventually we did not detect any products on the gels.
| |
| - |
| |
| - |
| |
| - | The pictures below present result of gel electrophoresis of PCR products.
| |
| - | *In most cases position of a band matches the expected length of DNA fragment. The only exception are GA1-2 and GA3-2 products. According to the position on the gel the length of these DNA fragments is 4-5kb, whereas the predicted length is 3.5kb. Our hypothesis is that we were provided [http://partsregistry.org/Part:pSB1AK3 pSB1AK3] backbone instead of [http://partsregistry.org/Part:pSB1A3 pSB1A3]backbone.
| |
| - | *For GA1-1, GA2-1, GA3-1 and GA4-1 we obtained two bands: 1000bp and 400bp, with the latter resulting from non-specific priming most probably. We extracted the two bands for GA1-1, GA2-1 and GA4-1 products, labelling the 1000kb and 400bp fragments GAX-1a and GAX1-b respectively.
| |
| - | *The molecular weight marker that we used in all gels is HyperLadder I, which produces regularly spaced bands ranging from 200 to 10,000bp.
| |
| - |
| |
| - | For the gel extraction of DNA we followed the [[Team:Cambridge/Protocols/Gel_Extraction_of_DNA | protocol]], assuming that one slice of gel is 100μl.
| |
| - |
| |
| - | ===Gibson Assembly===
| |
| - | We conducted Gibson Assembly of GA1, GA2, GA3 and GA4 constructs according to [Team:Cambridge/Protocols/Gibson_Assembly#Practice | the protocol]]. The volumes of Master Mix and solutions of amplified DNA were the following:
| |
| - |
| |
| - | {|
| |
| - | !GA1
| |
| - | !GA2
| |
| - | !GA3
| |
| - | !GA4
| |
| - | |-
| |
| - | |15µl Master Mix
| |
| - | |15µl Master Mix
| |
| - | |15µl Master Mix
| |
| - | |15µl Master Mix
| |
| - | |-
| |
| - | |2.5µl GA1-1a
| |
| - | |1.67µl GA2-1a
| |
| - | |2.5µl GA3-1
| |
| - | |1.67µl GA4-1a
| |
| - | |-
| |
| - | |2.5µl GA1-2
| |
| - | |1.67µl GA2-2
| |
| - | |2.5µl GA3-2
| |
| - | |1.67µl GA4-2
| |
| - | |-
| |
| - | |
| |
| - | |1.67µl GA2-3
| |
| - | |
| |
| - | |1.67µl GA4-3
| |
| - | |}
| |
| - |
| |
| - | ===Transformation===
| |
| - | ===Results===
| |
| - | ===Diagnostics===
| |
| - | ==Assembly: second attempt==
| |
| - | ===PCR===
| |
| - | ===Gibson Assembly===
| |
| - | ===Transformation===
| |
| - | ===Results===
| |
| - | ==What next?==
| |
| - |
| |
| - | {{Template:Team:Cambridge/CAM_2011_TEMPLATE_FOOT}}
| |
"
