Results

Solid Matrix

Our idea of a 3D-printer made it necessary to immobilize our cells inside a three dimensional matrix. We figured that the matrix needed to have the following properties:

1. Clear substance with good transmission of light to enable us to actuate the immobilized cells precisely with light.
2. Possibility to distribute the cells evenly within the matrix.
3. Environment that ensures the survival of the bacteria.

The idea to immobilize our bacteria in something like a solid growth medium (like agar-plates) was a step in the right direction, but standard LB-agar was not the solution. In the end, we chose GELRITE as a gelling agent, “a highly-purified, natural anionic heteropolysaccharide that forms rigid, brittle, agar-like gels” (source: gelrite spec sheet, see labbook/methods).

Clear substance with good transmission of light:

The matrix should be prepared with minimal media such as M9 instead of LB, because LB shows a strong absorption in the lower range of visible light (hence its yellow color). Minimal media are clear, which is a great advantage. The cell density in the matrix is also an important factor, because with increasing cell number the gel becomes blurry due to refraction of light (see diagrams).

Distribution of cells and cell survival:

To make sure that the cells are distributed evenly within the matrix, the bacteria need to be added to the medium before gelling occurs. The gelling temperature of GELRITE depends on both the amount of GELRITE powder and the salt concentration of the used liquid. A 0.5 % GELRITE gel prepared with M9 medium solidifies at around 46 °C. This means that the cells that shall be immobilized must survive such temperatures for a few minutes. This is why we made some experiments with the heat resistant E. coli strain BM28 (kindly provided by Jeanette Winter). Fluorescence microscopy showed that the cells can survive the gelling process and produce GFP or RFP upon induction. The temperature seems to be the most critical factor regarding cell survival, as minimal media, with which the gel is prepared, provide enough nutrients for the bacteria.

Diodes

As light sources we chose diodes, which should emit the wavelengths we need for activation of our sensors. As the blue light sensors peak absorbance is located at 465nm, [4] we chose a diode with an emission maximum at 470 nm. For the red light sensor two distinct diodes are needed. Activation of the sensor occurs at 705nm [3], therefore a diode which emits red light at 710nm was used. For the inactivation of the sensor the red light sensor shows a high absorption at 650nm, so we use a diode with an emission maximum of 650nm.

Cloning of AND-Gate and reporter constructs were successful and plasmids have been verified via sequencing after every cloning step. Those sequences were entered into the registry. The cloning scheme for our AND-Gate and reporter constructs can be seen on our Design page.

Red Light Sensor

Red Light Sensor with lacZ K322127

The red light sensor used is derived from BBa_K322127. We used this part in two ways: At first, we used PCR to amplify the parts needed for red light detection from this preexisting part, generating BBa_K568000. After that we compared the original part BBa_K322127 and our new part BBa_K568000. To prove the proper function of these two red light sensor parts, we did several Miller Assays. Unfortunately, this part did not produce the results we hoped for. Further testing would be needed for debugging.

Red light sensor with GFP

The part BBa_K568008, red light sensor with GFP was build to test BBa_K568000, which we use as red light sensor in our optogenetical AND-Gate BBa_K568001. We tested its function in JT2. The test of the assay was repeated several times. Our results indicate that the part is independed of the different light conditions active.

Blue Light Sensor

The blue light promoter was fused to lacZ and expression of lacZ was measured wih the Miller Assay. The blue light promoter can be induced at 450 nm, which we accomplished with the appropriate LED. To fully characterize this part, cultures were grown at different conditions and their lacZ expression was measured. Comparing samples grown at different lighting conditions showed that room light decreases the activity of the blue light promoter slightly, whereas blue light of 450 nm increases its activity.

As literature suggested a temperature dependency, we tested samples grown at room temperature (23 °C) and 37 °C, the usual incubation temperature for bacterial cultures. This proved that the blue light promoter yields higher expression rates at this lower temperature. Blue light is another input of a response pathway to cold stress and acts upon YcgF/YcgE. Under blue light the repressor YcgF binds to YcgE which in E. coli represses genes for biofilm formation, which then in turn detaches from its target. The underlying part for our construct is BBa_K238013, we added lacZ with a preceding RBS.

To analyze the three parameters of interest, temperature, light conditions and incubation time, for our blue light sensor together with two controls, we set up a very extensive test. The results were not as clear as we hoped, however confirmed first tendencies.

Reporter Plasmids

lacZ Reporter

We tested the function of our reporter plasmid BBa_K568003 using a Miller Assay. The part was transformed into BL21(DE3) cells, which are able to express T7 polymerase upon stimulation with IPTG. We were able to show that the expression level of β-galactosidase increases about one hour after induction, if compared to the control incubated without IPTG. The data indicates a leaky expression of β-galactosidase, which might be due to a leaky production of T7 polymerase by the host strain. An increase in Miller Units could be shown for all tested concentrations of IPTG between 0.01 mM and 1.5 mM, which seem to be quantitative until 90 min after stimulation. Congratulations! You have found our easter egg!

We repeated this experiment, applying an additional lower concenctration of 0.01 mM IPTG. For protein expression, this is a value below the normally proposed concentration. However, the experiment shows that the β-galactosidase is still strongly induced. We also tried to establish a positive control, using lacZ regulated by a constitutive promotor. This did not yield the expected results. Our cloning had not worked as expected, which we found out by sequencing our construct. There is also an additional data set at 30 min, which is presented in our Wiki. It yielded too high β-galactosidase levels, which might be due to a systematic error during this measurement. Nevertheless, the data shows most significantly that our lacZ reporter plasmid works and is activated in a quantitative way.

GFP Reporter

In order to test our AND-Gate construct in CP919 cells, we need another reporter than lacZ due to genomic ompC-lacZ fusion present in this strain. Therefore Part BBa_I746907 has successfully been tested for proper function. With saturating concentrations of IPTG the promoter was induced with t(1/2) of ca. 200 min.

Positive control-constitutive promoter with GFP

The part BBa_K568007 is used as a positive control in our GFP assays. We tested its function in JT2.

---