"
Team:Baltimore/Hardware
From 2011.igem.org
(Difference between revisions)
(→Current Hardware Stuff) |
(→Current Hardware Stuff) |
||
| (3 intermediate revisions not shown) | |||
| Line 21: | Line 21: | ||
*Remove block entirely and construct PCR from heated baths | *Remove block entirely and construct PCR from heated baths | ||
*A mixture of a few of these (simpler block with baths rather then tube shaped holes) | *A mixture of a few of these (simpler block with baths rather then tube shaped holes) | ||
| + | |||
| + | <br>Heating Rate: .7 to 1.1 C/S | ||
| + | <br>Cooling Rate: 2.0 C/S | ||
'''PCR Design:''' <br> | '''PCR Design:''' <br> | ||
[[File:Bmore_PCR_Design.png]] | [[File:Bmore_PCR_Design.png]] | ||
<br> | <br> | ||
| - | + | <br> | |
| - | ''Cheap PCR (maybe?)'''<br> | + | <br> |
| + | '''Cheap PCR (maybe?)'''<br> | ||
[[File:Bmore_CheapPCR_Design.png]] <br> | [[File:Bmore_CheapPCR_Design.png]] <br> | ||
| + | [[File:Bmore_CheapBlock_Design.png]] <br> | ||
| + | |||
| + | '''Software/Interfacing stuff''' | ||
| + | <br><br> | ||
| + | For the PCR interface software we need: <br> | ||
| + | *A menu bar with save, load, PCR settings, about, comm settings, connect, and disconnect | ||
| + | *A list box that allows us to add time/level points. | ||
| + | *A set of textboxes that we input new times/levels in (with a button) | ||
| + | *A picture box depicting the heating profile we are setting | ||
| + | *A set of textboxes/labels that indicate the current state of the PCR. | ||
| + | *A set of buttons, execute the current sequence, reset the sequence, and stop/pause the sequence. | ||
Latest revision as of 19:17, 22 August 2011
| Home | Team | Project | Parts Submitted to the Registry | Modeling | Notebook | Solutions | Safety | Attributions | Hardware | Material Safety Data Sheets | [http://partsregistry.org/assembly/libraries.cgi?id=35|MIT Parts Registry] |
|---|
Current Hardware Stuff
Tube shims:
Tube shims for centerfuge are finished. They will be uploaded to shapeways if anyone wants to get 'em.
Should be cheap. Will modify to cheapen.
PCR:
Current PCR block.
Quotes for it's manufacture are woefully high. Looking to decrease this cost. Prices:
- $950 (!!!) to have it 3D printed.
- ~$300 to $400 for a custom machining job.
- ??? Other methods of manufacture (sand casting, investment casting, ect...)?
Ways to possibly lower the cost:
- A Heat conductive polymer
- Some kind of putty (?? No idea what this was ??)
- Ceramic block
- Decrease size of block
- Remove hard to machine features
- Remove block entirely and construct PCR from heated baths
- A mixture of a few of these (simpler block with baths rather then tube shaped holes)
Heating Rate: .7 to 1.1 C/S
Cooling Rate: 2.0 C/S
PCR Design:
Cheap PCR (maybe?)
Software/Interfacing stuff
For the PCR interface software we need:
- A menu bar with save, load, PCR settings, about, comm settings, connect, and disconnect
- A list box that allows us to add time/level points.
- A set of textboxes that we input new times/levels in (with a button)
- A picture box depicting the heating profile we are setting
- A set of textboxes/labels that indicate the current state of the PCR.
- A set of buttons, execute the current sequence, reset the sequence, and stop/pause the sequence.
