Team:Bilkent UNAM Turkey/Experiment

We ordered our genes. We optimized codon usage because of gene taken from Enterobacter cloacae.
Codon Usage . We optimized our NFSI gene according to Chlamydomonas reinhardtii codon bias table provided by DNA 2.0. This program enables to change synonymous codons without changing amino acid sequence. You can also check the restriction sites while optimizing codons. We also avoided from forbidden restriction sites (EcoRI, XbaI, SpeI, PstI) therefore; we have chosen second frequently used codons for 34., 35., 38. and 45. amino acids.

Then we did restriction digestion and gel electrophoresis.
We repeated this step a lot because of failuire.I put correct result
Picture of restricted with EcoRI and PstI, nfsI gene







We used standard gel purification kit Our ligation style is really similar to iGEM's one.
Our one;
• insert volume(µl):X
• Cut Vector Volume(µl):X
• DEPC-water(µl):8,5-2X
• T4 DNA ligase(µl):0,5
• Ligation Buffer(µl):1
• Total Volume(µl):10

We transformed our plasmid into E.coli with a protocol.
We used invitrogen purification kit to get our plasmid. We sent genes to sequencing and sequencing data should be available on their link.

Polymerase Chain Reaction of GFP from pKScGFP

For 1.0µl of DNA we added,
• 1.0µl of forward primer
• 1.0µl of reverse primer
• 2.5µl of 10X PCR Buffer
• 0.5µl of MgSO4
• 0.5µl of dNTP mix
• 18.375µl of ddH2O
• 0.125µl of Taq polymerase

Parameters in thermal cycler were chosen as below:
Denaturation is 95oC for 4min
Annealing is 30 cycles:
• 95oC 1min
• 65oC 1min
• 72oC 2min
Extension 72oC for 10min
4oC hold

GFP fusion

GFP fusion with nfsI gene on our Biobrick is our plannned future work.

Restriction Enzyme Digestion

We obtained nfsI gene synthetically with prefix and suffixes. Synthetic nfsI gene was restriction digested via XhoI/BamHI to create sticky ends at prefix and suffixes.
We used pRbcRL as our backbone and as an algal expression plasmid. We restriction digested luciferase gene via XhoI/BamHI restriction enzymes and created a cut vector backbone with sticky ends.

DNA ligation

Then we ligated nfsI gene to the cut vector of pRbcRL (pRbc plasmid backbone) with insert:backbone ratios of 10:1, 3:1 and 1:1. All of them gave good results.

For 10:1 nfsI:pRbc ligation tube,

Solution	Volume (µl)
pRbc backbone 1.7
Insert nfsI 16.1
T4 ligase buffer (10X) 1
T4 DNA ligase 0.5
ddH2O 0.7
Total 20 For 3:1 nfsI:pRbc ligation tube, Solution Volume (µl) pRbc backbone 1.7 Insert nfsI 4.8 T4 ligase buffer (10X) 1 T4 DNA ligase 0.5 ddH2O 2 Total 10 For 1:1 nfsI:pRbc ligation tube, Solution Volume (µl) pRbc backbone 1.7 Insert nfsI 1.6 T4 ligase buffer (10X) 1 T4 DNA ligase 0.5 ddH2O 5.2 Total 10 Competent Escherichia coli DH5α were transformed with pRbcnfsI ligated products and plated to LB ampicillin plates. Colonies were collected after overnight incubation at 37oC, and miniculture was started from each colony. Plasmid DNA isolation was performed by using PureLink™ Quick Plasmid Miniprep Kit of InvitrogenTM. Nanodrop DNA concentrations after minipreps were as below: Nucleic Acid Conc. Unit A260 A280 260/280 260/230 Sample Type 361.4 ng/µl 7.228 4.334 1.67 1.82 DNA 384.9 ng/µl 7.698 4.554 1.69 1.82 DNA 558.7 ng/µl 11.174 7.232 1.55 1.65 DNA We proceeded to transformation of this plasmids to microalgae. We co-transformed Chlamydomonas reinhardtii to Tris-acetate-phosphate plus neomycine agar plates with pRbcnfsI and pKS-aphVIII-lox plasmid in order to select colonies based on the arginine deficiency in mutant strain cc-425 of Chlamydomonas reinhardtii. Next step was to collect colonies from plate. But due to time constraints we could not obtain colonies from this experiment yet. After collecting colonies, we plan to subculture colonies in the presence of trinitrotoluene (TNT) and check for change in its concentration. There is a problem with poping up if you see this note. Retrieved from "http://2011.igem.org/Team:Bilkent_UNAM_Turkey/Experiment" Recent changes What links here Related changes Special pages My preferences Printable version Permanent link Privacy policy Disclaimers