Team:Cambridge/Protocols/PCR

From 2011.igem.org

Revision as of 11:43, 21 July 2011 by Marta kkk (Talk | contribs)

Loading...
OVERVIEW
home

Contents

Polymerase Chain Reaction (PCR)

The goal of PCR is to amplify a section of DNA of interest for DNA analysis (e.g. gene insertion, sequencing, etc). The amplification rate is exponential.

Theory

Schematic drawing of the PCR cycle.
         (1) Denaturing at 94–96 °C 
         (2) Annealing at ~65 °C 
         (3) Elongation at 72 °C
Four cycles are shown here. The blue lines represent the DNA template to which primers ( red arrows ) anneal that are extended by the DNA polymerase ( light green circles ), to give shorter DNA products ( green lines ), which themselves are used as templates as PCR progresses. Credit, WikiMedia

The reaction works by the annealing of primers to single stranded DNA, which are extended by DNA polymerase. By repeating the process, the section of DNA between the primers is amplified.

During our project, we are using Phusion Hot Start II DNA Polymerase that is characterised by approximately 50-fold lower error rate than Thermus aquaticus Taq polymerase, which was the first thermostable polymerase used in PCR. The polymerase, in addition to having 5'→ 3' DNA polymerase activity, also possesses 3'→ 5' exonuclease activity.

The Phusion Polymerase allows us to perform Hot Start PCR - a modified version of PCR that avoids non-specific amplification of DNA. The Phusion Polymerase is reversibly bound to specific Affibody protein, which inhibits the DNA polymerase activity at ambient temperatures. Additionally, the Affibody ligand inhibits the 3'→ 5' exonuclease activity of the polymerase, preventing degradation of primers and template DNA during reaction setup. At polymerisation temperatures, the Affibody molecule is released, rendering the polymerase fully active.


TODO: More Here!

Practice

Reagents used in PCR reaction

The PCR reaction with Phusion Hot Start II DNA Polymerase contains the following reagents:

Name 50 μl reaction 20 μl reaction Final concentration
De-Ionized Water add to 50 μl add to 20 μl
5x Phusion Buffer 10 μl 4 μl 1x
10mM dNTPs 1 μl 0.4 μl 200μM each
Forward Primer x μl x μl 0.5 μM
Reverse Primer x μl x μl 0.5 μM
Template DNA x μl x μl
Phusion Polymerase 0.5 μl 0.2 μl 0.02 U/μl

Tip: The recommended buffer is 5x Phusion HF Buffer, used as a default buffer for high fidelity amplification.

Tip: When you receive primers synthesized by a biotechnological company

  • centrifuge tubes prior to opening to prevent loss of pelleted oligonucleotides (at 3000 rpm for 1 minute)
  • add the amount of deionized water specified in the table provided with primers to obtain 100 μM solution
  • prepare a 4-fold dilution of a portion of the primer solution


Only the primers and the DNA template are specific to the reaction. The remaining reagents can be made as a 'Master Mix' in order to reduce the need to repeatedly pipette small volumes which amplify experimental error.

As with all enzyme-containing reagents, the master mix should be kept in the freezer and small aliquots thawed when required.

The remainder of the reaction is handled automatically by a PCR machine. It is common practice to perform a gel electrophoresis to extract the correct DNA after PCR.

Condition of PCR reaction

An example of conditions we used for a PCR reaction using Phusion polymerase are as follows:

Cycle No. cycles Step Temp (C) Time (s)
1 1 1 98 30
2 30 1 98 10
2 55 30
3 72 2:30
3 1 1 72 5
4 50 1 4 99.59 (end)

Tip: Use 15-30 s/kb for extension. Do not exceed 1 min/kb.

Safety

No bacteria are used during the reaction there is therefore little or no biological hazard. Nevertheless, it is important to observe correct laboratory procedure and wear appropriate clothing and gloves. PCR occurs at high temperature, and this may present a risk, depending on the PCR machine employed.