Team:Macquarie Australia/Notebook

From 2011.igem.org

(Difference between revisions)
(Team PCR)
(Team PCR)
Line 16: Line 16:
* Step 1) We diluted the primer stock down to a concentration of 100uM. We did this by taking the weight of the primers and multiplying them by 100 and then adding this amount of water to the stock.   
* Step 1) We diluted the primer stock down to a concentration of 100uM. We did this by taking the weight of the primers and multiplying them by 100 and then adding this amount of water to the stock.   
-
:first indent So, for example, if our amount of Oligo = 38.3nM, we add 383ul of water (which gives us a concentration of 100uM)
+
::: So, for example, if our amount of Oligo = 38.3nM, we add 383ul of water (which gives us a concentration of 100uM)
* Step 2) We performed a second dilution (1:10) to produce a concentration of 10uM for each primer.
* Step 2) We performed a second dilution (1:10) to produce a concentration of 10uM for each primer.
-
So, 100uM  10uM
+
::: So, 100uM  10uM
* Step 3) A master-mix was made containing:
* Step 3) A master-mix was made containing:

Revision as of 00:58, 19 August 2011



Contents

Notebook

12/8/2011

Team PCR

Today, we started the PCR process in order to amplify our T7 promoter, HO1, At, Dr.

  • Step 1) We diluted the primer stock down to a concentration of 100uM. We did this by taking the weight of the primers and multiplying them by 100 and then adding this amount of water to the stock.
So, for example, if our amount of Oligo = 38.3nM, we add 383ul of water (which gives us a concentration of 100uM)
  • Step 2) We performed a second dilution (1:10) to produce a concentration of 10uM for each primer.
So, 100uM  10uM
  • Step 3) A master-mix was made containing:

Reactants Volume Water 41.4ul 5x buffer 16ul 10mM DNTP 1.6ul

  • Step 4) Mix was spun for a couple of seconds. This master mix as divided up into 4 15ul aliquots [you can take out 3 lots of 15ul and keep the final 15ul in the mastermix tube and use that as a housing].
  • Step 5) To these 15ul aliquots, we add into each:

Primers (from steps 1-2) and template Volume Forward 2ul Reverse 2ul Plasmid template [Ho, Dr etc] 1ul

What we end up with is 4 reaction tubes with our plasmid template, the primers in the correct dilution. However, we have not put in the taq polymerase yet.

  • Step 6) We set up the PCR machine with the following protocol:

Initial denaturation – 94oC for 2 minutes

Denaturation – 94oC for 30 sec Annealing – 60oC for 30 seconds ] 10 cycles in total Extension – 72oC for 2min 30sec

THEN

Denaturation – 94oC for 30 sec Annealing – 52oC for 30 seconds ] 15 cycles in total. Extension – 72oC for 2min 30sec


Final extension – 72oC for 10 min Hold period – 4oC for 2 minutes

We’ve labelled the protocol ‘330’ and it’s the same as last years’ protocol with a few additions. Note that we made a mistake during our 15 cycle stage - it should be at 72oC. Our bad.

  • Step 7) We conducted our PCR! It took 2 hours and 13 minutes to complete.
  • Step 8) With our PCR complete, we then set about preparing the Chloramphenicol vector [which is the one we need to submit for any medal] as well as the clean up protocol.

Ch vector prep

Reactants Volume DPN1 1ul Xba1 + Spe1 1ul + 1ul 100x BSA 1ul Template DNA - Ch vector 20ul 10x NEBuffer 4 5ul Water 21.5ul Total 50.5ul

Clean up prep:

Sigma GENELUTE PCR clean up kit has the protocol

  • Step 9) We set up the nanodrop to determine the quality of our PCR results:


PCR product Concentration T7 1.1ug [23ng/ul] Ho 870ng [17.4ng/ul] Agro 500ng [10.4ng/ul] Dino 1.8ug [36.1ng/ul]

  • Step 10) Cleaned PCR products were diluted with water [20ul PCR product + 30ul water] and were then double digested using X + S [1ul each] in 5ul of 10x buffer and 1ul of BSA.

Media Prep

-LB media Method- Dissolve 10g trytone, 5g yeast extract and 10g NaCl in 800 mL MilliQ water, making use of a magnetic stirrer. Once dissolved, bring volume up to 1 litre using the MilliQ water. Autoclave 500 mL of the solution (121oC, 15 min, standard liquid cycle).

-LB agar Method- Add 7.5 g Bacto agar to the remaining 500 mL of LB media and autoclave [121oC, 15 min, standard liquid cycle]. Add 250 µL of Chloroamphenicol and mix well before plating out and setting agar.

After cooling and antibiotic addition, the LB agar was plated out using aseptic technique. 14 LB agar plates were prepared and allowed to cool next to the bunsen. After this all plates were aseptically sealed using parafilm and stored in the refridegerator.


SOC prep

In order to prepare and transform competent E.coli cells various nutrient broths, such as LB, LB agar, SOC and SOB medium, were prepared. SOC and SOB medium are known to result in higher transformation efficiencies of plasmids (1). The SOC media was prepared using the following guidelines:

2% w/v bacto-tryptone (20 g)

0.5% w/v bacto-yeast extract (5 g)

8.56mM NaCl (0.5 g)

2.5mM KCl (0.186 g)

20mM MgSO4 (2.408 g)

20mM glucose (3.603 g)

Distilled H2O to 1000 mL (2)

It was decided that over the course of the project only 200ml of SOC media would be needed. Therefore the above values were adjusted to the following quantities:

2% w/v bacto-tryptone (4 g)

0.5% w/v bacto-yeast extract (1 g)

400 µl 5M NaCl

250 µl 2M KCl

20mM MgSO4 (0.4821 g)

20mM glucose (0.7222 g)

MilliQ H2O to 200 mL

The adjusted quantities were combined in 1l measuring column with constant stirring and then placed in the autoclave for sterilization.




1. Hanahan, D. (1983) J Mol Biol 166, 557-580

2. Sambrook, J. (1989) Molecular Cloning: A Laboratory Manual, 2nd Ed ed., Plainview, NY