Team:ETH Zurich/Biology/Cloning

From 2011.igem.org

(Difference between revisions)
(Diffusion test in tubes)
(Plasmid list)
Line 238: Line 238:
'''Backbones'''
'''Backbones'''
-
'''Plasmid for test system'''
+
'''Plasmids for test system'''
'''Plasmids for part characterization'''
'''Plasmids for part characterization'''
-
'''Plasmid for final system'''
+
'''Plasmids for final system'''
|}
|}

Revision as of 02:41, 21 September 2011

Menu image preload Menu image preload Menu image preload Menu image preload Menu image preload Menu image preload


Material and methods
Protocols Plasmid list Primer list
All protocols, plasmids and primers can be found here.

Protocols

[http://www.neb.com/nebecomm/DoubleDigestCalculator.asp Double digest] for cloning

Variant 1 Variant 2
Plasmid
  • x µl Plasmid (~2 µg if possible)
  • 2 µl EcoRI
  • 2 µl XbaI
  • 5 µl buffer 4
  • 0.5 µl BSA
  • adjust to 10 µl ddH2O
  • x µl Plasmid (~2 µg if possible)
  • 3 µl PstI
  • 2 µl Spe I
  • 5 µl buffer 2
  • 0.5 µl BSA
  • adjust to 10 µl ddH2O
Insert
  • x µl Insert (~2 µg if possible)
  • 2 µl EcoRI
  • 3 µl Spe I
  • 5 µl buffer 1
  • 0.5 µl BSA
  • adjust to 10 µl ddH2O
  • x µl Insert (~2 µg if possible)
  • 3 µl XbaI
  • 2 µl Pst 1
  • 5 µl buffer 3
  • 0.5 µl BSA
  • adjust to 10 µl ddH2O


⇒ incubate for 2 h at 37°C and gel purify

Ligation

  1. Ligation mix
    • 1:5 ratio of plasmid backbone : Insert
    • 1 µl 10 x T4 Ligase buffer (vortex)
    • 0.5 µl T4 Ligase
    adjust to 10 µl with ddH2O
  2. Let the mixture stay for 1h at room temperature
  3. Denature the ligase at 65 °C for 5 min

Transformation

  1. Thaw competent cells on ice.
  2. Add 200 µl cells to 10 µl ligation mix
  3. Place the mixture put them on ice for 30 min
  4. Heatshock 30 sec at 42 °C
  5. Place the mixture again on ice for 2 min
  6. Add 4 x SOC medium (800 µl)
  7. Let them grow for 60 min at 37 °C
  8. Spin cells down for 5 min at low speed
  9. Remove the supernatant, resuspend the cells
  10. Spread 100 µl of the cells onto the plates.

PCR

PCR mixture

  • 10 µl 10x Phusion buffer
  • 1 µl 10 mM dNTPs
  • 2.5 µl 10 µM forward primer
  • 2.5 µl 10 µM reverse primer
  • 1 ng DNA template
  • 0.2 µl Phusion polymerase
  • optional DMSO

adjust to 50 µl with ddH2O

PCR procedure

  • initial denaturation: 98 °C for 30 sec
  • 35 cycles
    • denaturation: 98 °C for 5 sec
    • annealing: annealing temperature (see Primer list) for 10 sec
    • extension: 72 °C for 30 sec per kb
  • final extension: 72°C for 5 min
  • storage at 4°C

Colony PCR

pick a colony and resuspend in 10 µl ddH2O

PCR mixture

  • 1 µl colony
  • 1 µl 10x taq buffer
  • 0.8 µl dNTPs
  • 0.05 µl 10 µM forward primer
  • 0.05 µl 10 µM reverse primer
  • 0.1 µl Taq

adjust to 10 µl with ddH2O

PCR procedure

  • initial denaturation: 95 °C for 30 sec
  • 25 cycles
    • denaturation: 95 °C for 30 sec
    • annealing: 55 °C for 30 sec
    • extension: 68 °C for 90 sec
  • final extension: 68 °C for 5 min
  • storage at 4 °C

Preparation of glycerol stocks

From the overnight cultures 15 % glycerol were made and stored at -20 °C

AlcR testing

  • preparatory overnight culture of JM101 with AlcR-testsystem in LB medium
  • cultures in M9 minimal medium
  • all final experiments were done in 15 ml falcons with 3 ml cells
  • AlcR production was induced with either 0, 1, 100 ng/ml anhydrotetracycline added at 4 °C
  • For AlcR activation 0, 10, 1000 µM acetaldehyde was added at 4 °C
  • Cells were incubated at 37 °C in closed tubes
  • Fluorescence of GFP was measured after 1 h, 2 h and over night, all measurements were done in triplicates

Chemically competent E. coli (JM 101)

1 M MOPS

  • 10.46 g MOPS

Total 50 ml

1 M CaCl2•2H2O

  • 7.35 g CaCl2

Total 50 ml

3 M KOAc

  • 14.72 g KOAc

Total 50 ml

TFBI

  • 1.2 g RbCl
  • 0.99 g MnCl2•4H2O
  • 1 ml 1 M CaCl2
  • 1 ml 3 M KOAc
  • 15.33 ml glycerol 100 %

Total 100 ml; bring to pH 5.8 with 0.2 N acetic acid; filter sterilize

TFBII

  • 0.048 g RbCl
  • 3 ml 1 M CaCl2
  • 0.4 ml 1 M MOPS pH 7
  • 7 ml glycerol 100 %

filter sterilize

Preparation

  • add 0.5 ml fresh O/N culture to 250 ml LB medium
  • shake at 37 °C until OD600 is 0.5-0.7
  • cool on ice, spin down at 4 °C/ 3000rpm/ 5 min, put pellet on ice
  • resuspend pellet in 5 ml TFBI with pipet, add 70 ml cool TFBI, incubate on ice for 2-4 h
  • aliquot suspension into pre-cooled tubes, 200 µl each
  • freeze aliquots immediately in dry ice, store at -80 °C

Chemically competent E. coli (DH5α)

Done according to the [http://openwetware.org/wiki/Preparing_chemically_competent_cells_%28Inoue%29 protocol] of OpenWetWare

Antibiotics

ampicillin kanamycin chloramphenicol

Diffusion test in tubes

  • agarose with E. coli with IPTG inducible GFP were filled in different tubes
  • on end of the tube was put in a IPTG solution

Mediums

SOB

  • 0.5 % (w/v) yeast extract
  • 2 % (w/v) tryptone
  • 10 mM NaCl
  • 2.5 mM KCl
  • 20 mM MgSO4

adjust to pH 7.5 by adding 1M NaOH

SOC

  • SOB
  • 20 mM glucose

LB medium

  • 10 g Bacto-tryptone
  • 5 g yeast extract
  • 10 g NaCl

Total 1 l

M9 minimal medium

10x M9

  • 12.8 g Na2HPO4
  • 3 g KH2PO4
  • 0.5 g NaCl
  • 1 g NH4Cl

Total 100 ml

autoclave seperatly

  • 10 x M9
  • 1 M MgSO4
  • 1 M CaCl2
  • 1 % (w/v) thiamine solution
  • 20 % (w/v) glucose


Plasmid list

Backbones

Plasmids for test system

Plasmids for part characterization

Plasmids for final system


Primer list

Synthesized parts

  • LacIM1
  • AlcR (codon optimized)